It’s time for one of the most important steps: removing any standing water from the home. The removal process is actually much less complicated than you may think. Contractors use fancy shop vacuums and rotate them around the room, sucking up all the water that’s present in the area. The amount of time this phase takes varies depending on the type of substrate that’s being dried, the size of the room and the total amount of water that’s present.

Today’s precision welding shops specializing in plastic injection mold, dies and tooling repair have a wide range of new technologies available to enhance their ability to provide the highest level of quality, craftsmanship, and service to their clients. One of the fastest growing technologies is the use of manual laser welding systems as an alternative to traditional microscope GTA welding.

After this type of catastrophic event, it's typically best to replace certain types of equipment rather than try to recover items such as receptacles, light switches, start-stop stations, fire alarm panels, and metering equipment. Your crews must also drain all the conduits by opening up the conduit covers and letting gravity drain out all water and debris.

Among the most common and most preventable causes of water damage are burst pipes. Burst pipes typically happen because of clogs and freezing. Prevent the damage by finding a family plumber to do annual inspections. Regular inspections and maintenance are a cost-effective, preventative measure. Installing new plumbing typically runs between $350 to $2,000.
The information and advice contained in this article is intended as a general guide for informational purposes only. It does not take into account your personal situation. While we at Resolve have significant experience and history operating in the home restoration industry and working closely with construction contractors, we are not licensed as a general or specialty contractor. We encourage you to consider the information we’ve provided but urge you not to rely upon it in place of appropriate professional advice from a licensed, experienced construction contractor.    

The third type is black water, such as sewage or serious flooding from nearby rivers, etc. This water contains waste, bacteria and other serious contaminants. Black water can cause very serious health problems, and you shouldn’t try to clean it up yourself. It’s time to contact the pros for home water damage repair. Water damage cleanup cost rises to $7 per square foot.

The project documentation manager should make sure the camera memory sticks are downloaded to a folder located on the site server. Each picture will be opened and saved in a folder labeled by the appropriate power center or room number. There are two pictures associated with each piece of equipment, both of which should be labeled using the sequence number. After saving the pictures on the local server, the memory sticks will be erased and ready for use the next day.
Dalworth Restoration Crews are certified through the IICRC and receive specialized training at our Dallas/Fort Worth Restoration Facility. Our technicians are trained to professionally perform water damage restoration services according to the best practices and ANSI/IICRC S500 standards. Technicians are available 24/7 for emergency water removal, cleanup and content repair, as well as rebuild and restore your water or flood damaged property to pre-loss condition.

Water damage is a serious problem that needs immediate attention fast. The faster water damage is treated, the more furniture and valuable items are saved from permanent damage. Water damage may happen at any time and the most common cause is flooding. Floods may be caused by natural disasters such as hurricanes and excessive rainfall. Sometimes flooding may occur due to leaking faucets, broken sewage pipes, and waste buildup under sink drains.
Today’s precision welding shops specializing in plastic injection mold, dies and tooling repair have a wide range of new technologies available to enhance their ability to provide the highest level of quality, craftsmanship, and service to their clients. One of the fastest growing technologies is the use of manual laser welding systems as an alternative to traditional microscope GTA welding.
Laser is an acronym for “Light Amplification by the Stimulated Emission of Radiation.” This technology produces a sharply focused beam of hot light that melts a very small area of metal and can be used to join similar or dissimilar alloys. The laser welding process can be performed quickly (normally in milliseconds) and does not scar or blemish the welding surface. In fact, by adjusting the laser’s beam diameter, a smooth, near polished finish can be achieved with the laser welder. Since very little heat is generated at the weld point, users can easily weld 0.10mm away from the most complicated and intricate machined patterns, polished surfaces and removable component assemblies.
Accurate mold and tooling component assembly is a critical step in mold repair—and is the origin of many preventable, unscheduled mold stops (breakdowns). Poor workmanship and mistakes are usually a result of too much speed, lack of focus or physical skills, and disorganized work habits. If several repair techs are involved in the assembly of a mold, communication breakdowns between them can require the mold to be disassembled yet again to correct an oversight or install something that was forgotten.
When flooding happens, it would be best to call our Dallas Water Damage office right away. The faster the situation is controlled, the better chances of everything restored in their pre-loss state. Upholstered furniture, Persian carpets, oriental rugs, floor carpets, wooden cabinets, and other valuable home items will undergo full restoration by our Dallas Water Damage quality service technicians.

For more than 10 years, homeowners all around the Dallas and Ft Worth area have called on us for immediate assistance with water restoration services for flooding and water emergencies. We have the resources and experience to deal with any kind of water situation quickly and efficiently. When your home or business has had a flood, you really don’t want to leave a voice mail for someone to call you back during “normal business hours.” Water damage doesn’t care what time it is, and neither do we. We are available 24/7 to take care of your water problem now.
It is possible to recover from a catastrophic event with a more reliable system than before. However, the speed and efficiency of the recovery will depend on the availability and accuracy of documentation. In preparation or planning for the recovery of an electrical system, the facility should ensure that all drawings/documentation are up to date and a copy is kept in a safe location that can be accessed after the event.
When you’re sure the mold has been eliminated, seal the wood surfaces with pigmented shellac like BIN or an oil-based primer like KILZ. Repaint cleaned wall surfaces with a regular latex paint that contains a mildewcide to help stop future mold growth. Then install new insulation and drywall and nail the trim back on. And keep in mind that if the moisture returns, mold will return.
If temperatures tend to freeze in your area, be sure to protect your pipes. Insulate both hot and cold water pipes using heat tape or pipe sleeves available in your home improvement store. If you have water supply lines in your garage, keep the garage door closed as often as possible. Open kitchen and bathroom cabinet doors to allow warmer air to circulate. If you plan to spend some time away from your home, leave the heat on and set your thermostat to at least 55 degrees. You can’t control the weather, but you can put up a good fight to save your pipes.
At Dallas Water Damage, we pride ourselves with superior workmanship and consistent quality of service. With our 24 hour emergency call-in service, we offer free consultation advice on our water damage services as well as our carpet cleaning options. We understand the importance of having a 100% bacteria and virus free home in order to avoid health risks for our family. That’s why, aside from water damage services, our professional technicians also perform regular household cleaning and disinfecting.
Remove all of the drywall from the wall if the wrong type of drywall was initially installed. On rare occasions, mold damage results from using the wrong type of drywall for a particular application. The two most common causes of mold damage, not created by water leaks, are drywall installed behind tile, or regular drywall installed in a bathroom instead of mold resistant drywall.
While there are currently no government regulations in the United States dictating procedures, two certifying bodies, the Institute of Inspection Cleaning and Restoration Certification (IICRC) and the RIA, do recommend standards of care. The current IICRC standard is ANSI/IICRC S500-2015.[9] It is the collaborative work of the IICRC, SCRT, IEI, IAQA, and NADCA.
×