Dalworth Restoration Crews are certified through the IICRC and receive specialized training at our Dallas/Fort Worth Restoration Facility. Our technicians are trained to professionally perform water damage restoration services according to the best practices and ANSI/IICRC S500 standards. Technicians are available 24/7 for emergency water removal, cleanup and content repair, as well as rebuild and restore your water or flood damaged property to pre-loss condition.
At WaterBear, our water damage Hillsboro specialists understand that a flood in your home or business is emotionally devastating. It takes up valuable time and wreaks havoc on your day-to-day activities. That’s why we offer the best in drying technology, equipment and training to get you back to the life you’re used to as quickly as possible. Our proprietary Dry-In-Place technology places us among the nation’s leaders in Water Damage Mitigation. From our years of experience we have learned that a quick response is the key to limiting damage and potential mold growth in any water damage situation. We strive to get your life back to the way you want it as quickly as possible.
Inspect the defects. To find the source of the defects, we perform a visual inspection as high as 24x magnification, use dye-penetrant inspection (DPI), or use fluorescent penetrant inspection (FPI). This allows us to find small pits, microscopic cracks and larger cracks in the gate. If these defects are not identified and repaired, more problems can arise for the gate and the mold.
From wet carpets to swollen floorboards, it’s often evident when water has damaged your floor. But if you aren’t sure, it’s important to check immediately in case moisture has become trapped underneath. Note that underlayment and padding are particularly susceptible to water damage and must usually be removed. However, this also presents an opportunity to install new, waterproof flooring in the area. Ceramic tile, high-end vinyl and certain engineered wood materials can all help protect floors against future water damage repair.
Despite what you might think, a flooded home can be saved rather than razed to the ground, but removing the moisture quickly is key. "The biggest thing is getting in there and getting it cleaned up quickly," says Robyn Kent, claims administrator at Dalworth Restoration, based in Euless, TX. "Closer to the three- to five-day mark is when it becomes questionable, since by then, all the materials have become fragile."
Locate and repair the source of the leak. The source of the problem is usually apparent once you remove the drywall and expose the framing. If the leak source is not easily determined, consult a licensed contractor before you replace the drywall. You must repair the cause of the leak or mold and mildew will eventually reform over the new drywall. An unresolved leak may also create additional damage to framing, insulation, siding and flooring.
Ice dams and other roof problems can also cause water damage to siding materials as well. Here, the biggest danger is water seeping in behind your siding and causing permanent damage to more vulnerable materials. So if this happens, you will need to remove or replace the siding quickly before rot sets in. Water can also seep in behind faux stone and other external walls around your home. So it’s important to be thorough in this inspection.
Clean water that originated from a source that does not pose substantial harm to humans. Examples include: broken water supply lines, melting ice or snow, falling rainwater, broken toilet tanks, and toilet bowls that do not contain contaminants or additives. Clean water may deteriorate with time as it dissolves or mixes with soils and other contaminants.
We offer structural drying, as after the immediate water emergency has been resolved with damage restoration, your house and its contents still need to be thoroughly dried out. We have specialized equipment that is able to get this done in as short a time as possible, and with minimal disruption. Our commercial-grade water extractors will get your carpet and other flooring back to nearly 100% dry condition. We also use high-speed blowers to circulate air at high volumes throughout the house in order to facilitate the drying process.
Laser is an acronym for “Light Amplification by the Stimulated Emission of Radiation.” This technology produces a sharply focused beam of hot light that melts a very small area of metal and can be used to join similar or dissimilar alloys. The laser welding process can be performed quickly (normally in milliseconds) and does not scar or blemish the welding surface. In fact, by adjusting the laser’s beam diameter, a smooth, near polished finish can be achieved with the laser welder. Since very little heat is generated at the weld point, users can easily weld 0.10mm away from the most complicated and intricate machined patterns, polished surfaces and removable component assemblies.
Category 2 Water - Refers to a source of water that contains a significant degree of chemical, biological or physical contaminants and causes discomfort or sickness when consumed or even exposed to. Known as "grey water". This type carries microorganisms and nutrients of micro-organisms. Examples are toilet bowls with urine (no feces), sump pump failures, seepage due to hydrostatic failure and water discharge from dishwashers or washing machines.