Mildew is a surface type of mold that won’t damage your home’s structure. But other types of mold cause rot. Remove mildew from wood when you probe the suspect area with a screwdriver or other sharp tool (Photo 3). If the wood is soft or crumbles, the fungi have taken hold and rot has begun. We’ll show you how to remove mold from wood in a few steps.
Mold growth can be controlled on surfaces by cleaning with a non-ammonia detergent or pine oil cleaner and disinfecting with a 10% bleach solution. (Caution: Never mix ammonia and bleach products, as the resulting fumes can be highly toxic.) Always test this solution on a small area of the item or area you’re cleaning to be sure it doesn’t cause staining or fading.
Unlike sites which blend pricing from dissimilar jobs, Homewyse estimates are based on the Unit Cost method. This method uses job specific detail for superior pricing accuracy and transparency - and has become an industry standard through publications and guidance of leading trade associations, including: PHCCA, the NKBA, the NECA, the AIA, and the ASPE.
Most of us are very familiar with lockout/tagout procedures, test-before-touch practices, and applying safety grounds. While these are key safety aspects of putting equipment into an electrically safe condition, there are other safety items that need to be addressed when working in a natural disaster area. Items such as air quality, structural issues, and chemical spill exposure come into play. It is the responsibility of each company to keep its own people safe and supply them with special personal protective equipment (PPE), such as rubber boots, respirators, dust masks, portable gas monitors, and rubber gloves. As a service company, you must also coordinate with plant safety personnel you've contracted with to develop special safety procedures to address the ever-changing site conditions. Frequent safety meetings are a must to keep everyone up to date with the most current hazard conditions on the site.
Showers, tubs, sinks, toilets, windows, and doors. Water leaks around bathtubs, showers, sinks, and toilets can cause damage because the leak is often out of sight. To prevent leaks, make sure you have a watertight seal of caulk around tubs, sinks, toilets, tubs, shower stalls, windows, and doors. Cracks or mold on caulk or tile grout may indicate that you don't have a watertight seal. Remove all caulk or grout, clean and dry the surface thoroughly, and apply fresh caulk. Don't apply new caulk or grout on top of the old materials.
After a sketch is made of the piece of equipment, add the equipment to a detailed electrical equipment tracking sheet, which should include general information such as the item number, sequence number, priority, area of the plant, power center or room number, transformer, substation, cell position, equipment type, circuit identification, plant identification number, manufacturer, percent water level, model number, frame size, and voltage. After completing these procedures on all the equipment associated with a power center or a piece of gear, the QA/QC leader must review the documentation for accuracy. Once the documentation has been approved, the equipment is ready for removal.
Mold can develop within 24 to 48 hours of a flood, says Ashley Small of FEMA, so remove wet contents, including carpeting and bedding, as soon as possible. If an item has been wet for less than 48 hours, it may be salvageable. However, you’ll need to decide whether it holds enough monetary or sentimental value to try to do so. And notify your insurance company before removing items to ensure that you’re not affecting coverage. Always photograph the flood-soaked items.
Many parts of a car are challenging to clean and dry because they are hard to access. Door locks, window regulators, power seat motors, heating and air conditioning components, and many small parts are tucked away in enclosed areas or up under the dash. These items may work okay immediately following a flood, only to fail later due to contamination by dirty water.
Different removal methods and measures are used depending on the category of water. Due to the destructive nature of water, chosen restoration methods also depend heavily on the amount of water, and on the amount of time the water has remained stagnant. For example, as long as carpet has not been wet for longer than 48 hours, and the water involved was not sewage based, a carpet can usually be saved; however, if the water has soaked for longer, then the carpet is probably irreparable and will have to be replaced. Water damage restoration can be performed by property management teams, building maintenance personnel, or by the homeowners themselves; however, contacting a certified professional water damage restoration specialist is often regarded as the safest way to restore water damaged property.