Dalworth Emergency Restoration Crews are available 24/7 to extract water, remove debris, dry out and repair your residential or commercial property quickly. Call us at 817-203-2944 if you have had a water loss and need assistance. We will dispatch our certified technician(s) to your home or office to resolve your water damage using our state-of-the-art drying equipment.
If temperatures tend to freeze in your area, be sure to protect your pipes. Insulate both hot and cold water pipes using heat tape or pipe sleeves available in your home improvement store. If you have water supply lines in your garage, keep the garage door closed as often as possible. Open kitchen and bathroom cabinet doors to allow warmer air to circulate. If you plan to spend some time away from your home, leave the heat on and set your thermostat to at least 55 degrees. You can’t control the weather, but you can put up a good fight to save your pipes.
Among the most common and most preventable causes of water damage are burst pipes. Burst pipes typically happen because of clogs and freezing. Prevent the damage by finding a family plumber to do annual inspections. Regular inspections and maintenance are a cost-effective, preventative measure. Installing new plumbing typically runs between $350 to $2,000.
Once you’ve pulled away wet materials and established holes or cuts in the wall as needed, you’ll typically need one air mover for every 15 – 25 square feet of floor, unless the moisture load and density is particularly high, then you may need more. To prevent mold, make sure all of the layers and materials are dry before putting everything back together.
Our plumbing and water damage restoration experts are well-trained and knowledgeable in handling a water damage emergency whenever the situation strikes. Our trained professionals receive the Institute of Inspection, Cleaning and Restoration Certification (IICRC) and they’ll always perform emergency water damage services in compliance with the highest standards for professional water damage restoration. Roto-Rooter’s vehicles are fully equipped with state-of-the art water extraction, drying and moisture testing equipment to handle everything including:
If your water bill is unusually high, that might be an indication of an undetected leak. Buying a water leak sensor that sends alerts to your phone is one way to safeguard your home. You should also check around your toilets, tubs, showers and sinks for any soft spots or moisture. Keep an eye out for loose tiles as well. If you have a dishwasher or a refrigerator with a water line, look for warped or discolored floorboards.
Our water damage technicians first determine the cause of flooding in your home before beginning the process of draining, cleaning, and restoring. The water damage cause plays a vital role in the water damage process. When flooding is caused by natural calamities, there’s a higher chance of bacteria buildup in the affected areas and calls for immediate disinfection. Other water damage causes do not pose health threats and require only the basic process of restoration.
If you repair damage resulting from an appliance-related leak, you need to get a Certificate of Appliance-Related Water Damage Remediation (WDR-1). The certificate verifies that the damage was properly replaced or repaired and that any related physical damage was properly remediated, repaired, or replaced. If you don't have the repairs or remediation certified by a WDR-1, an insurance company can deny you coverage in the future based on previous appliance-related damage or claims.

If the moisture damage has been neglected or gone unnoticed for long, you’re likely to find rot. Where possible, remove and replace soft, spongy studs and wall sheathing. Where removal is difficult, treat the affected areas with a wood preservative (available at home centers), after cleaning the wood and allowing it to dry. Then double up rotted members with pressure-treated wood.


Roofs. Keep roofs free of debris that can damage roofing and allow water to seep in. Trim tree branches to prevent them from rubbing and damaging the roof. Repair missing or damaged shingles. Properly seal any cracks around chimneys, skylights, and vents. Check metal flashing for holes, cracks, or other damage. Replace flashing or use silicone caulk to seal any openings.
Melting Ice & Snow: With spring comes nicer weather, but also the occasional risk of flooding in areas that cannot fully absorb all the water. When temperatures fluctuate from day to day, melted ice can refreeze and cause a whole other set of problems. Due to this hazard, it is extremely important to keep an eye on the weather and fix the problem as soon as it occurs.
During the walkthrough, compile a list of flooded equipment to help you estimate man-power requirements and create a preliminary schedule of repair work. As mobilization of crews begins, start developing job strategies, such as finding office space, living accommodations, and transportation for crews. You must also think about arranging food/catering services and developing work schedules. Once your crews have been mobilized and job-site safety requirements are met (see SIDEBAR: Developing a Safety Plan Following a Natural Disaster), it's time to go to work.
Believe it or not, there are three types of water. The first type is “clean” water from rain, condensation, leaky pipes, and so on. It’s relatively harmless to clean it up yourself. But if you decide to seek outside help, it costs around $3.75 per square foot for basic water damage cleanup (replacements not included). The second type is gray water, slightly dirty water from dishwashers, washing machines, clean toilets, and so on. And it may have some contaminants. But you can clean it up yourself if you remove it carefully and with proper safety gear to protect yourself. Professional water damage cleanup cost rises to $4.50 per square foot.
If you have to remove mold concentrations or perform any black mold removal covering more than a few square feet, where the musty odor is strong or where you find extensive water damage, we recommend that you take special precautions. You want to not only avoid contaminating the rest of the house but also protect yourself from breathing high concentrations of spores and VOCs.
Once help arrives, the first thing a water mitigation contractor will do is inspect the home and evaluate the damage. In order to properly evaluate the damage, they have special tools and instruments they use to measure the moisture content of the home. To do this, they either poke or rest the instruments on top of surfaces like floors, baseboards and ceilings in the damaged rooms to get an accurate reading. Depending on the moisture content readings and Institution of Inspection Cleaning and Restoration Certification (IICRC) dry standards for the state you live in, your contractor will assess if drying equipment is needed.
The methods for dealing with damage to walls depend on the type of materials and also what’s behind those materials. Drywall can often be salvaged, when you respond quickly to damage. You can purchase moisture meters that allow you to assess structural integrity. If the integrity checks out then your drying approach will depend on wall contents. If the wall has insulation, you will need to use flood cuts. If there is no insulation, then usually the best method is to create weep holes. And if you’re dealing with a firewall, you’ll want to use staggered cuts.
×