BRAVO – job well done! Discovered a flood at home in San Francisco – water had been over flowing a 2nd floor sink for 15 hours. Contacted Allied, signed work order on line and workers were at the house within 15 minutes. They brought a truck load of equipment to mitigate the damage. Drying fans were installed, heating pads were placed on hardwood floors, walls and ceilings were opened and drying and dehumidifying tubes installed. Excellent, professional care. Very pleased with their swift delivery of emergency service AND their attention to detail to ensure the water damage was dried out completely.

Despite what you might think, a flooded home can be saved rather than razed to the ground, but removing the moisture quickly is key. "The biggest thing is getting in there and getting it cleaned up quickly," says Robyn Kent, claims administrator at Dalworth Restoration, based in Euless, TX. "Closer to the three- to five-day mark is when it becomes questionable, since by then, all the materials have become fragile."
The electrical systems in modern cars are particularly prone to flood water damage. Engine control computers, vehicle sensors, infotainment systems, and other electronic devices – along with wiring harnesses and the many connectors that join them together – can be very difficult to salvage. Unless every part is thoroughly cleaned and dried, inside and out, problems caused by corrosion can crop up weeks or even months after the flooding.
A leaky faucet, cracked bathtub, or failing toilet can easily become a much larger and costlier problem. A 120-square foot bathroom can cost as much as $3,000 to clean up and repair. Homeowners spend an average of about $300 when hiring a plumber, but can save thousands in future expenses. More importantly, homeowner's insurance typically does not cover damage due to ignored maintenance issues.
Important: Abrasive stones break down during mold and die polishing, grinding, tool sharpening, and dressing of cutting & grinding wheels. The resulting dust is classified by OSHA as inert or nuisance dust. Please consult the Material Safety Data Sheet for each stone; data provided therein pertains primarily to the dust produced during and after use. Please note that hazards may change when abrasive stones are used in conjunction with solvents, cutting fluids or other chemicals. For more complete information, consult the Material Safety Data Sheets of chemical products used with abrasive stone products.
Remove all of the drywall from the wall if the wrong type of drywall was initially installed. On rare occasions, mold damage results from using the wrong type of drywall for a particular application. The two most common causes of mold damage, not created by water leaks, are drywall installed behind tile, or regular drywall installed in a bathroom instead of mold resistant drywall.
At this stage, put away all measuring instruments and hand tools and focus on how best to clean the tool. The type, frequency, and method of cleaning molds should be based on cycles, hours, or production in conjunction with mold-specific factors (resin, residue, vent location and capacity, tooling concerns, etc.) that will dictate the cleaning level and process.
The information and advice contained in this article is intended as a general guide for informational purposes only. It does not take into account your personal situation. While we at Resolve have significant experience and history operating in the home restoration industry and working closely with construction contractors, we are not licensed as a general or specialty contractor. We encourage you to consider the information we’ve provided but urge you not to rely upon it in place of appropriate professional advice from a licensed, experienced construction contractor.    
Surface molds grow in just about any damp location, such as the grout lines of a ceramic tiled shower. They’re easy to scrub away with a mold cleaner mixture of 1/2 cup bleach, 1 qt. water and a little detergent. In mold remediation, the bleach in the cleaning mixture kills the mold, and the detergent helps lift it off the surface so you can rinse it away so it won’t return as fast. You can also buy a mildew cleaner at hardware stores, paint stores and most home centers.
Fire and Water Restoration companies are regulated by the appropriate state's Department of Consumer Affairs - usually the state contractors license board. In California, all Fire and Water Restoration companies must register with the California Contractors State License Board.[10] Presently, the California Contractors State License Board has no specific classification for "water and fire damage restoration."
×