BRAVO – job well done! Discovered a flood at home in San Francisco – water had been over flowing a 2nd floor sink for 15 hours. Contacted Allied, signed work order on line and workers were at the house within 15 minutes. They brought a truck load of equipment to mitigate the damage. Drying fans were installed, heating pads were placed on hardwood floors, walls and ceilings were opened and drying and dehumidifying tubes installed. Excellent, professional care. Very pleased with their swift delivery of emergency service AND their attention to detail to ensure the water damage was dried out completely.
In mold repair, structure is especially critical when working with many pieces of close-fitting tooling that are nested into plates. Remembering the type, fit, relational position of components, and the sheer volume of tooling in some molds can be overwhelming enough without adding confusion about where you are in the process of the repair. In shops where two repair techs are usually assigned to a mold, time can be saved by working in a organized approach.

It’s important to understand the differences because Category 2 and Category 3 water present health risks to your employees and customers and need to be handled differently. The most likely sources of clean water would be water from a pipe, water heater, steam lines or even rainwater. The basic rule of thumb is that it should look and smell like tap water.
Throughout the drying process, crews will stop by periodically to monitor how the drying is progressing. Specifically, they monitor the dehumidifiers’ intake and output temperatures and humidity levels to make sure the dehumidifiers aren’t putting wet air out into the room. They’ll also go back and take readings of the same surfaces they did during the inspection phase. As rooms are declared dry, crews will often move equipment around to other areas of the home that are still wet.
For instance, if you remove 16 ejector pins from a mold and notice that a couple of them feel tight, will you remember which ones were tight later on, when you peruse past records to discover that galling pins have been a problem for the past five production runs? Knowing this information before you split or disassemble a mold removes some of the guesswork involved when looking for the root cause.
Public insurance adjusters are independent adjusters who help people negotiate claims with their insurance companies. Public adjusters work for you, not the insurance company. They charge you a fee for their services. The fee is usually a percentage of the claim and is subtracted from any settlement you get from your insurance company. You don't have to hire a public adjuster.
When the next water damage call comes in for a flood cleanup due to a broken water pipe or drain backup, make sure you have all the commercial restoration equipment on hand that you need to tackle the job in a moment’s notice. Events like floods, hurricanes, wildfires and other natural disasters can leave homes and businesses in peril and in need of professional restoration services.
AAA recommends that you plan ahead for vehicle service by finding an auto repair shop and technician you can trust before you need them. AAA.com/AutoRepair provides information on nearly 7,000 Approved Auto Repair facilities that have met AAA’s high standards for appearance, technician training and certification, insurance coverage and customer satisfaction. AAA regularly inspects every Approved Auto Repair facility and surveys their customers to ensure ongoing performance. In addition, AAA members receive special benefits that include auto repair discounts, an extended 24-month/24,000-mile parts and labor warranty, and AAA assistance in resolving repair-related issues.
Before any mold is released for production (“blue-tagged”), it is imperative to put the mold through a series of final-check bench procedures to verify “All Systems Go” and minimize any opportunities for the mold to be stopped and returned to the shop for something that should have been caught before it was released. Water leaks, heater problems, etc., can be avoided with a final-check procedure.
Gone were helpful clues for the repair technicians who had yet to begin troubleshooting and analyzing mold performance and wear. So now, how will the repair techs determine if the 63-day production run was too long? Or whether the leader pins, bushings, and interlocks were greased properly during the run? And how will they know if all the swishing during cleaning did not create any “dings” in the sleeves that could be blamed on something else instead of poor cleaning practices? Other questions will remain unanswered, too: Does the mold still have excess vent residue in the top right quadrant? Were all the ejector sleeves numbered and in the proper mold position before they were removed?

The information in this publication is current as of the revision date. Changes in laws and agency administrative rules made after the revision date may affect the content. View current information on our website. TDI distributes this publication for educational purposes only. This publication is not an endorsement by TDI of any service, product, or company.
Our water damage technicians first determine the cause of flooding in your home before beginning the process of draining, cleaning, and restoring. The water damage cause plays a vital role in the water damage process. When flooding is caused by natural calamities, there’s a higher chance of bacteria buildup in the affected areas and calls for immediate disinfection. Other water damage causes do not pose health threats and require only the basic process of restoration.
The water restoration process is an important one. Using the right procedures and materials can help people save cherished belongings and even prevent their homes from being condemned. Water restoration companies specialize in mitigating the effects of water, but the success for water damage restoration depends on the severity of the damage and the amount of water that caused the damage. Water restoration companies may hire outside experts to assess a property and determine a water restoration and water removal plan. These water restoration companies typically use high-tech equipment and well-documented procedures to control water damage. Water in basement areas may only require a short cleanup process, but water in other areas of a property will require extensive remediation.
Whatever the mess, whether you discovered flooding from a broken or leaky pipe, damage from frozen pipes, a sewer line break, a sink or toilet overflow, or a malfunctioning appliance like a water heater, washing machine, dishwasher or refrigerator in your home, or you’re a victim of storm damage, our Hillsboro flood damage technicians are equipped to handle any problem. WaterBear is here for all water cleanup and restore your home or business back to normal, quickly and right the first time. Acting fast against flood damage can increase the chance of salvaging usable materials, reducing costs, and saving time, so we guarantee a fast response and professional guidance to help you sort out the options, work with your insurance agent and get flood cleanup and restoration underway.
Roofs should be inspected annually. A professional roof contractor can look for exterior and interior warning signs that your roof’s condition may lead to water damage, including cracked or missing shingles and areas where water is prone to pool. An inspection can cost several hundred dollars, but in exchange for your peace of mind, it’s priceless.
Water damage can originate by different sources such as a broken dishwasher hose, a washing machine overflow, a dishwasher leakage, broken/leaking pipes, flood waters and clogged toilets. According to the Environmental Protection Agency, 13.7% of all water used in the home today can be attributed to plumbing leaks.[3] On average that is approximately 10,000 gallons of water per year wasted by leaks for each US home. A tiny, 1/8-inch crack in a pipe can release up to 250 gallons of water a day.[4] According to Claims Magazine in August 2000, broken water pipes ranked second to hurricanes in terms of both the number of homes damaged and the amount of claims (on average $50,000 per insurance claim[citation needed]) costs in the US.[5] Experts suggest that homeowners inspect and replace worn pipe fittings and hose connections to all household appliances that use water at least once a year. This includes washing machines, dishwashers, kitchen sinks and bathroom lavatories, refrigerator icemakers, water softeners and humidifiers. A few US companies offer whole-house leak protection systems utilizing flow-based technologies. A number of insurance companies offer policy holders reduced rates for installing a whole-house leak protection system.
×