If temperatures tend to freeze in your area, be sure to protect your pipes. Insulate both hot and cold water pipes using heat tape or pipe sleeves available in your home improvement store. If you have water supply lines in your garage, keep the garage door closed as often as possible. Open kitchen and bathroom cabinet doors to allow warmer air to circulate. If you plan to spend some time away from your home, leave the heat on and set your thermostat to at least 55 degrees. You can’t control the weather, but you can put up a good fight to save your pipes.
Though not the most common precipitator of water damage repair in the NH, storm flooding can cause serious short term and long-term problems to your residential or commercial property. The likelihood of flood-water damage to your property is rising, and property owners need to be prepared to deal with this very real possibility.  Flooding from seasonal storms is more common than you’d think, and the problems that arise from it need to be addressed as quickly as possible.
If the moisture damage has been neglected or gone unnoticed for long, you’re likely to find rot. Where possible, remove and replace soft, spongy studs and wall sheathing. Where removal is difficult, treat the affected areas with a wood preservative (available at home centers), after cleaning the wood and allowing it to dry. Then double up rotted members with pressure-treated wood.
Drying - We determine the amount and type of drying equipment needed. Typically, we install a combination of drying fans, dehumidifiers, and negative air machines. We examine many factors (such as when the loss occurred, the magnitude of water damage, and size of the affected areas) to determine the best drying strategy to utilize as well as the quantity of equipment necessary. 
Richard Covert, FLOWER MOUND, TX, Nov 17th, 2014: What a great group of professionals! Everyone was great to work with, accommodating, understanding, sympathetic but focused on getting the mess cleaned up and getting the property ready to be put back together. What a miserable thing to have happen but thankfully there are professionals like these to help you through it. 
Mildew is a surface type of mold that won’t damage your home’s structure. But other types of mold cause rot. Remove mildew from wood when you probe the suspect area with a screwdriver or other sharp tool (Photo 3). If the wood is soft or crumbles, the fungi have taken hold and rot has begun. We’ll show you how to remove mold from wood in a few steps.
In the event of water damage, Mr. Restore is the company to call in Dallas. Not only do we offer 24/7 emergency services, but we are also on site within the hour. Our complete restoration services include advanced drying technologies. Our project managers are certified through the American Drying Institute and can ensure that the damage is little to none. We are family owned and operated in Dallas and offer free evaluations to those who contact us for restoration service or environmental remediation. We pride ourselves on being a total restoration and cleanup company. We handle all of our projects in with the highest level of expertise and experience.
You can easily spot the most visible type of mold, called mildew, which begins as tiny, usually black spots but often grows into larger colonies. It’s the black stuff you see in the grout lines in your shower, on damp walls, and outdoors on the surfaces of deck boards and painted siding, especially in damp and shady areas. A mildewed surface is often difficult to distinguish from a dirty one. To test for mildew, simply dab a few drops of household bleach on the blackened area. If it lightens after one to two minutes, you have mildew. If the area remains dark, you probably have dirt.
The project documentation manager should make sure the camera memory sticks are downloaded to a folder located on the site server. Each picture will be opened and saved in a folder labeled by the appropriate power center or room number. There are two pictures associated with each piece of equipment, both of which should be labeled using the sequence number. After saving the pictures on the local server, the memory sticks will be erased and ready for use the next day.

Cut through the paper facing of the drywall sheet with a razor knife. Cut along the drawn lines. Break the drywall along the face cut, and fold the drywall slightly to make a crease in the paper backing of the drywall sheet. Cut through the crease in the backing paper with a razor knife from the backside of the drywall sheet, and remove the unwanted portion of drywall. To make cuts that are perpendicular to each other, use a keyhole saw for the shorter of the two cuts, and then fold and cut the drywall.
Believe it or not, there are three types of water. The first type is “clean” water from rain, condensation, leaky pipes, and so on. It’s relatively harmless to clean it up yourself. But if you decide to seek outside help, it costs around $3.75 per square foot for basic water damage cleanup (replacements not included). The second type is gray water, slightly dirty water from dishwashers, washing machines, clean toilets, and so on. And it may have some contaminants. But you can clean it up yourself if you remove it carefully and with proper safety gear to protect yourself. Professional water damage cleanup cost rises to $4.50 per square foot.
Heavy rain, rapidly melting snow, rising rivers, and breaches in levees or dikes can cause vehicle flood damage and the need for difficult and expensive auto repairs. Once floodwaters rise above the vehicle door openings, extensive disassembly may be required for cleaning. To avoid causing additional problems, never attempt to start a flood-damaged car until a thorough vehicle inspection has been performed by a qualified technician.
You can find out how old your water heater is by looking up the serial number on the manufacturer’s sticker near the top of the water heater. Make sure to regularly inspect your water heater to check for signs of moisture build-up, mold or corrosion. If your water isn’t as hot as it used to be or there’s rust coming from your faucets, it’s time to call a plumber or water heater specialist.
To prevent water damage, you should replace your washing machine supply hose at least once every five years. Also, resist the temptation to overload your washing machine. Constantly stuffing too many clothes into your washing machine could loosen gaskets and valves or cause cracks. Take good care of your washing machine and your washing machine will take good care of you.
If you’ve recently experienced a flood or pipe burst and have water damage in your home, you’re probably wondering “what happens now?” The first, and most important, step when dealing with water or flood damage is to stop any active leaks in the home. This can be done by shutting off the home’s main water supply. If you don’t know how to shut off your home’s water supply, call a professional plumber or your local water supply company for assistance. Once any active leaks have been addressed and all water has been turned off, it’s imperative you call a professional to start the water damage cleanup process as quickly as possible to minimize damage.
Damage from long standing water falls in this class, like river flooding or storm surges from a hurricane. It has saturated materials such as stone, brick, and hardwood. These materials have low permeance — meaning they do not soak up liquids quickly. Time is the primary factor in this category. With a higher cost of cleanup and repair, it is important to get problems diagnosed and solved as quickly as possible.
Inspect the defects. To find the source of the defects, we perform a visual inspection as high as 24x magnification, use dye-penetrant inspection (DPI), or use fluorescent penetrant inspection (FPI). This allows us to find small pits, microscopic cracks and larger cracks in the gate. If these defects are not identified and repaired, more problems can arise for the gate and the mold.
Today’s precision welding shops specializing in plastic injection mold, dies and tooling repair have a wide range of new technologies available to enhance their ability to provide the highest level of quality, craftsmanship, and service to their clients. One of the fastest growing technologies is the use of manual laser welding systems as an alternative to traditional microscope GTA welding.
Everything could be fine in your house as you sleep at night. However, it only takes a broken pipe, water heater, washing machine, fire, or a sudden major storm, to cause major water damage to your home. When you are overwhelmed with water you need to do something about it now, and you can depend on your water damage restoration professionals to be there when you need them.
For more than 10 years, homeowners all around the Dallas and Ft Worth area have called on us for immediate assistance with water restoration services for flooding and water emergencies. We have the resources and experience to deal with any kind of water situation quickly and efficiently. When your home or business has had a flood, you really don’t want to leave a voice mail for someone to call you back during “normal business hours.” Water damage doesn’t care what time it is, and neither do we. We are available 24/7 to take care of your water problem now.
You may also wish to hire a flood restoration service—you can find pros under “Flood” or “Disaster recovery” in your local phone book, or check with the Better Business Bureau, local Chamber of Commerce, or contractor recommendation sites, such as Angieslist.com or MerchantCircle.com. Look for those with Institute of Inspection, Cleaning, and Restoration Certification.
5 stars to the team at Allied. Geronimo and his partner saved the day when they came to my home after a severe leak had damaged my closet and bedroom. They acted quickly and professionally to dry the rooms out and prepare them for being restored. I was so pleased and relieved to work with this team. This includes the professionalism of Misty who took my initial call. She knew how stressed I was and was right there to help me with a plan of action – all leading to a great result! Thanks so much! Sarah in Santa Rosa
Fire and Water Restoration companies are regulated by the appropriate state's Department of Consumer Affairs - usually the state contractors license board. In California, all Fire and Water Restoration companies must register with the California Contractors State License Board.[10] Presently, the California Contractors State License Board has no specific classification for "water and fire damage restoration."
×