Even a competent DIYer should have a qualified professional assess the damage first — making sure no part of the cleanup is missed. Before doing anything, check with your insurance company — they may require a licensed assessment. Don't wait. As soon as you detect any damage, call a professional. With time, each class and category quickly degrades into something worse.
And even if you do have flood insurance, you should make sure what is covered. "Many people don't realize their homeowner insurance doesn't cover rising water," says Kent. In other words, "some flood insurance will cover rain water if it comes through your roof, but most of the time, it won't cover water rising in your home, like what's happening in Texas, unless you ask for it specifically."
Most of us are very familiar with lockout/tagout procedures, test-before-touch practices, and applying safety grounds. While these are key safety aspects of putting equipment into an electrically safe condition, there are other safety items that need to be addressed when working in a natural disaster area. Items such as air quality, structural issues, and chemical spill exposure come into play. It is the responsibility of each company to keep its own people safe and supply them with special personal protective equipment (PPE), such as rubber boots, respirators, dust masks, portable gas monitors, and rubber gloves. As a service company, you must also coordinate with plant safety personnel you've contracted with to develop special safety procedures to address the ever-changing site conditions. Frequent safety meetings are a must to keep everyone up to date with the most current hazard conditions on the site.
It’s time for one of the most important steps: removing any standing water from the home. The removal process is actually much less complicated than you may think. Contractors use fancy shop vacuums and rotate them around the room, sucking up all the water that’s present in the area. The amount of time this phase takes varies depending on the type of substrate that’s being dried, the size of the room and the total amount of water that’s present.
To further ensure a safe and effective environmental remediation, our crews are rigorously trained in mold removal procedures approved by the Indoor Air Quality Association (IAQA); Institute of Inspection, Cleaning and Restoration Certification (IICRC); the Restoration Industry Association (RIA); and our own in-house trainers. In addition, all of our superintendents, operations managers, project managers, project directors and regional managers hold Certified Mold Remediation (CMR) certifications.
At WaterBear, our water damage Hillsboro specialists understand that a flood in your home or business is emotionally devastating. It takes up valuable time and wreaks havoc on your day-to-day activities. That’s why we offer the best in drying technology, equipment and training to get you back to the life you’re used to as quickly as possible. Our proprietary Dry-In-Place technology places us among the nation’s leaders in Water Damage Mitigation. From our years of experience we have learned that a quick response is the key to limiting damage and potential mold growth in any water damage situation. We strive to get your life back to the way you want it as quickly as possible.
Hurricanes and river flooding are common natural causes, as are high water tables and improperly graded ground. Installing a sump pump and water alarm are sensible preventions in areas with high water tables. The sump pump will pump water from under the foundation to drain it away from the home and averages about $1,200 to install. The sump pump itself will cost between $50 to $400. Also, ground that slopes towards the basement of the home can lead to leakage in the basement and increased stress on sewage systems.
The electrical systems in modern cars are particularly prone to flood water damage. Engine control computers, vehicle sensors, infotainment systems, and other electronic devices – along with wiring harnesses and the many connectors that join them together – can be very difficult to salvage. Unless every part is thoroughly cleaned and dried, inside and out, problems caused by corrosion can crop up weeks or even months after the flooding.
At this stage, put away all measuring instruments and hand tools and focus on how best to clean the tool. The type, frequency, and method of cleaning molds should be based on cycles, hours, or production in conjunction with mold-specific factors (resin, residue, vent location and capacity, tooling concerns, etc.) that will dictate the cleaning level and process.
Appliance hoses. Broken hoses are among the most common causes of water damage. Regularly inspect hoses and hose fittings on washing machines, icemakers, and dishwashers for kinks, cracks, bulges, or deterioration. Replace standard rubber washing machine hoses every two to five years or more often if they are showing signs of wear. Consider using steel-reinforced hoses for longer life.
Hillsboro homes that are left vacant with no regulating of heat or poorly insulated walls can be a common culprit of frozen water pipes and frozen water lines in the winter time. These breaks can be hard to notice immediately because they commonly occur in the basement. Broken pipes can also be common cause of water damage, causing gallons of water to come flooding through your living rooms, bedrooms, kitchen and bathroom. Water pipe bursts are common in areas of extreme winter cold and high winds that drive the wind chill well below freezing temperatures. Pipes that lack proper insulation and are exposed to the winter’s cold are far more likely to create a need for restoration.
To prevent water damage, you should replace your washing machine supply hose at least once every five years. Also, resist the temptation to overload your washing machine. Constantly stuffing too many clothes into your washing machine could loosen gaskets and valves or cause cracks. Take good care of your washing machine and your washing machine will take good care of you.
When industrial facilities are faced with such a catastrophic event, specific and detailed steps must be taken to return the facility to productive operation. In the wake of this type of natural disaster, it's especially critical to analyze and repair the electrical power system in a safe and logical sequence (see SIDEBAR: Temporary and Emergency Power). Following is an overview of how to approach recovery operations of electrical equipment after a flood.
Inspect damaged materials for mold and mildew. Mold can start to grow in the right conditions in as little as 24 hours. For long-term issues, like mold caused by attic condensation, the mold may have started growing a long time ago. And if you find mold and mildew issues, you need to be very careful. Some mold is toxic to humans, and all mold is very damaging to the materials it infests. For small mold issues, cut out the material, bag it, and throw it away immediately. For serious mold issues, get out of the area, shut down any airflow (to avoid spore contamination) and call a professional. And keep in mind that mold can show up in hidden areas like inside walls or under floors, so this inspection and water damage repair will be ongoing.
Once our restoration team removes the moisture from your home or business, we then will begin repairing and restoring the property. The length of this process depends on the extent of damage. Our team of trained technicians uses all the latest technology and top industrial equipment to remove the moisture and prevent further damage. The sooner that we are contacted, the less damage can affect your property. We offer emergency services and can arrive at your home or business almost immediately. Call Mr. Restore in Dallas today for a free evaluation of the services we provide.
It is possible to recover from a catastrophic event with a more reliable system than before. However, the speed and efficiency of the recovery will depend on the availability and accuracy of documentation. In preparation or planning for the recovery of an electrical system, the facility should ensure that all drawings/documentation are up to date and a copy is kept in a safe location that can be accessed after the event.
The resulting damage is a different than the initial damage.For example, if water damage resulting from a broken pipe, or appliance is listed in your wording as covered, then you may be compensated for a portion of the damages caused even though the deteriorated pipe replacement or a new appliance would not be covered. This is an example the cause of the damage not being covered, but the resulting damage being covered.
If you have a replacement cost policy, most insurance companies pay claims with two checks. The insurance company will give you the first check after the adjuster has reviewed your damage. This check will be for the estimated cost of repairs, minus depreciation and your deductible. A deductible is the amount of the claim that you're responsible for paying yourself. Review your policy or ask your agent or adjuster if you don't know how much your deductible is.