We can provide dehumidification for your property. This goes along with the mold removal and prevention process. The living areas of your home should not have humidity; this is normally taken care of by your central air conditioning system. However, if your AC ductwork has a crack or leak, or if your home does not have central air, the interior of your house may sometimes have damp or humid air. The dehumidification process eliminates that and saves you the headache of mold removal down the road.
It’s important to understand the differences because Category 2 and Category 3 water present health risks to your employees and customers and need to be handled differently. The most likely sources of clean water would be water from a pipe, water heater, steam lines or even rainwater. The basic rule of thumb is that it should look and smell like tap water.
When you’re sure the mold has been eliminated, seal the wood surfaces with pigmented shellac like BIN or an oil-based primer like KILZ. Repaint cleaned wall surfaces with a regular latex paint that contains a mildewcide to help stop future mold growth. Then install new insulation and drywall and nail the trim back on. And keep in mind that if the moisture returns, mold will return.
After a mold has been cleaned, repaired, changed over, and final-checked, it needs to be given a new status and moved to one of three areas—typically racked in holding/storage area, reset in the press, or staged as a back-up mold in a molding-cell operation. It could also go to an outside vender for rebuild or production. You should know where your molds are.
Roofs should be inspected annually. A professional roof contractor can look for exterior and interior warning signs that your roof’s condition may lead to water damage, including cracked or missing shingles and areas where water is prone to pool. An inspection can cost several hundred dollars, but in exchange for your peace of mind, it’s priceless.
Mold growth can be controlled on surfaces by cleaning with a non-ammonia detergent or pine oil cleaner and disinfecting with a 10% bleach solution. (Caution: Never mix ammonia and bleach products, as the resulting fumes can be highly toxic.) Always test this solution on a small area of the item or area you’re cleaning to be sure it doesn’t cause staining or fading. 
You may also wish to hire a flood restoration service—you can find pros under “Flood” or “Disaster recovery” in your local phone book, or check with the Better Business Bureau, local Chamber of Commerce, or contractor recommendation sites, such as Angieslist.com or MerchantCircle.com. Look for those with Institute of Inspection, Cleaning, and Restoration Certification.
Our highly trained technicians are ready to respond immediately to flood or water damage at your Columbus property. We have the experience, expertise, and training to restore your home or business quickly and properly. We use advanced inspection and extraction equipment to find the water and remove it as quickly as possible. Our technicians will monitor and document the drying process to ensure your property is back to normal.
Mold is a major-league nuisance. It blackens the grout lines in your shower, discolors drywall, shows up as black spots on siding, darkens decks, and grows on and rots damp wood everywhere. Even worse, it can be bad for your health. Mold releases microscopic spores that cause allergic reactions, runny noses and sneezing, as well as irritating, even injurious, odors. We’ll cover how to remove mold, how to get rid of black mold, how to kill mold on wood and what kills mold in a few steps.
Locate and repair the source of the leak. The source of the problem is usually apparent once you remove the drywall and expose the framing. If the leak source is not easily determined, consult a licensed contractor before you replace the drywall. You must repair the cause of the leak or mold and mildew will eventually reform over the new drywall. An unresolved leak may also create additional damage to framing, insulation, siding and flooring.
In the United States, those individuals who are affected by widescale flooding may have the ability to apply for government and FEMA grants through the Individual Assistance program.[1] On a larger level, businesses, cities, and communities can apply to the FEMA Public Assistance program for funds to assist after a large flood. For example, the city of Fond du Lac Wisconsin received $1.2 million FEMA grant after flooding in June 2008. The program allows the city to purchase the water damaged properties, demolish the structures, and turn the properties into public green space.[2]
×