Locate and repair the source of the leak. The source of the problem is usually apparent once you remove the drywall and expose the framing. If the leak source is not easily determined, consult a licensed contractor before you replace the drywall. You must repair the cause of the leak or mold and mildew will eventually reform over the new drywall. An unresolved leak may also create additional damage to framing, insulation, siding and flooring.

This information is not intended as an offer to sell, or the solicitation of an offer to buy, a franchise. It is for information purposes only. Currently, the following states regulate the offer and sale of franchises: California, Hawaii, Illinois, Indiana, Maryland, Michigan, Minnesota, New York, North Dakota, Oregon, Rhode Island, South Dakota, Virginia, Washington, and Wisconsin. If you are a resident of or want to locate a franchise in one of these states, we will not offer you a franchise unless and until we have complied with applicable pre-sale registration and disclosure requirements in your state.
You can easily spot the most visible type of mold, called mildew, which begins as tiny, usually black spots but often grows into larger colonies. It’s the black stuff you see in the grout lines in your shower, on damp walls, and outdoors on the surfaces of deck boards and painted siding, especially in damp and shady areas. A mildewed surface is often difficult to distinguish from a dirty one. To test for mildew, simply dab a few drops of household bleach on the blackened area. If it lightens after one to two minutes, you have mildew. If the area remains dark, you probably have dirt.
Your insurance company will only pay for additional living expenses up to your policy's ALE dollar limits. Because repairs on your home can sometimes take months, monitor your expenses carefully to make sure you have enough ALE to cover the entire time you’ll be out of your home. If you reach your policy's ALE dollar limits before your home is fully repaired, you’ll have to pay the rest of the expenses out of your own pocket.
Inspect the defects. To find the source of the defects, we perform a visual inspection as high as 24x magnification, use dye-penetrant inspection (DPI), or use fluorescent penetrant inspection (FPI). This allows us to find small pits, microscopic cracks and larger cracks in the gate. If these defects are not identified and repaired, more problems can arise for the gate and the mold.
The insurance company will pay to repair your home with materials of like kind and quality to the original. For example, if the carpet was damaged, the insurance company will pay to replace the damaged carpet with carpet of a similar grade and quality. If you choose to upgrade the carpet or change the type of flooring, you will have to pay the extra costs yourself.
Remove all of the drywall from the wall if the wrong type of drywall was initially installed. On rare occasions, mold damage results from using the wrong type of drywall for a particular application. The two most common causes of mold damage, not created by water leaks, are drywall installed behind tile, or regular drywall installed in a bathroom instead of mold resistant drywall.

Today’s precision welding shops specializing in plastic injection mold, dies and tooling repair have a wide range of new technologies available to enhance their ability to provide the highest level of quality, craftsmanship, and service to their clients. One of the fastest growing technologies is the use of manual laser welding systems as an alternative to traditional microscope GTA welding.


Damage from long standing water falls in this class, like river flooding or storm surges from a hurricane. It has saturated materials such as stone, brick, and hardwood. These materials have low permeance — meaning they do not soak up liquids quickly. Time is the primary factor in this category. With a higher cost of cleanup and repair, it is important to get problems diagnosed and solved as quickly as possible.
Showers, tubs, sinks, toilets, windows, and doors. Water leaks around bathtubs, showers, sinks, and toilets can cause damage because the leak is often out of sight. To prevent leaks, make sure you have a watertight seal of caulk around tubs, sinks, toilets, tubs, shower stalls, windows, and doors. Cracks or mold on caulk or tile grout may indicate that you don't have a watertight seal. Remove all caulk or grout, clean and dry the surface thoroughly, and apply fresh caulk. Don't apply new caulk or grout on top of the old materials.
Once help arrives, the first thing a water mitigation contractor will do is inspect the home and evaluate the damage. In order to properly evaluate the damage, they have special tools and instruments they use to measure the moisture content of the home. To do this, they either poke or rest the instruments on top of surfaces like floors, baseboards and ceilings in the damaged rooms to get an accurate reading. Depending on the moisture content readings and Institution of Inspection Cleaning and Restoration Certification (IICRC) dry standards for the state you live in, your contractor will assess if drying equipment is needed.
Though a competent DIY homeowner may be able to clean up and repair some damage, it's important to have a professional assess it first to determine the extent and any underlying conditions. Missing even a small amount, or its causes, can lead to costlier repairs later. Even small quantities of moisture may result in mold growth. Plus, undiagnosed causes will lead to recurrences. For instance, fixing a damaged ceiling but not the leaky roof that caused it will only lead to another wrecked ceiling.

Hillsboro homes that are left vacant with no regulating of heat or poorly insulated walls can be a common culprit of frozen water pipes and frozen water lines in the winter time. These breaks can be hard to notice immediately because they commonly occur in the basement. Broken pipes can also be common cause of water damage, causing gallons of water to come flooding through your living rooms, bedrooms, kitchen and bathroom. Water pipe bursts are common in areas of extreme winter cold and high winds that drive the wind chill well below freezing temperatures. Pipes that lack proper insulation and are exposed to the winter’s cold are far more likely to create a need for restoration.
In addition, it’s important to have a working flashlight and turn off all water and electrical sources within the home, says Dr. Maurice A. Ramirez, author of “The Complete Idiot’s Guide to Disaster Preparedness.” Even if the power isn’t operational, it’s a good idea to go to your fuse box and turn off the main, plus all of the individual fuse connections. That way, if the power is reactivated, you’re not at risk for mixing standing water and electricity.
Our plumbing and water damage restoration experts are well-trained and knowledgeable in handling a water damage emergency whenever the situation strikes. Our trained professionals receive the Institute of Inspection, Cleaning and Restoration Certification (IICRC) and they’ll always perform emergency water damage services in compliance with the highest standards for professional water damage restoration. Roto-Rooter’s vehicles are fully equipped with state-of-the art water extraction, drying and moisture testing equipment to handle everything including:
We offer mold prevention services, as any place in your home that has constant moisture is susceptible to mold growth. Mold is often detected by smell, but the problem of mold goes far beyond the odor it creates. Mold creates an unhealthy environment, and many people have severe allergic reactions when they are in the presence of mold or mildew. Any mold that is in your home now must be completely eliminated. More importantly, we can also remove the source of the moisture that allows the mold to begin thriving in the first place. It does no good to get rid of the mold if the conditions remain that allow it to grow again. We can do a thorough assessment of your home and advise you on the best course of action.
You should expect a fully trained Hillsboro water damage repair technician at the door who’s ready to begin to work immediately after a thorough inspection of the problem. Having our own fleet and equipment, allows us to get the water damage cleanup done faster than many other companies. Our business success depends upon restoring your life back to normal regardless of the Hillsboro water damage and the mess it caused. This is our passion and our clients will tell you so. Our professional staff is working 24/7 to make sure your call is answered by a real person. Give us a call at any time, day or night.

Appliance hoses. Broken hoses are among the most common causes of water damage. Regularly inspect hoses and hose fittings on washing machines, icemakers, and dishwashers for kinks, cracks, bulges, or deterioration. Replace standard rubber washing machine hoses every two to five years or more often if they are showing signs of wear. Consider using steel-reinforced hoses for longer life.
Coastal Surge: If you live by the ocean, rising tides and seasonal storms can cause flooding to your property. When a high tide corresponds with a storm, it can be a recipe for disaster. As well as those right along the coast, other properties set slightly off from the ocean can also be at risk. High winds from the storm can also help water infiltrate and damage buildings and land.
Water damage is often caused by plumbing issues. That’s why it’s important to inspect the plumbing systems in your home at least once a year to ensure that there aren’t any problems with hoses or pipe joints. You should also keep in mind that plumbing pipes have a long lifespan. Brass pipes can last for as many as 70 years while copper pipes can last for more than 50 years. The average lifespan for galvanized steel pipes is often between 20 and 50 years.
Before you remove any water or make any repairs, fully document the damage for your insurer by taking photos or video. Digital versions are best, says Ramirez, because they can be stored electronically and easily copied. If you start removing water or making repairs before you photograph the damage, you could potentially decrease the extent of your coverage, he says.
If you’ve recently experienced a flood or pipe burst and have water damage in your home, you’re probably wondering “what happens now?” The first, and most important, step when dealing with water or flood damage is to stop any active leaks in the home. This can be done by shutting off the home’s main water supply. If you don’t know how to shut off your home’s water supply, call a professional plumber or your local water supply company for assistance. Once any active leaks have been addressed and all water has been turned off, it’s imperative you call a professional to start the water damage cleanup process as quickly as possible to minimize damage.
×