Remove all of the drywall from the wall if the wrong type of drywall was initially installed. On rare occasions, mold damage results from using the wrong type of drywall for a particular application. The two most common causes of mold damage, not created by water leaks, are drywall installed behind tile, or regular drywall installed in a bathroom instead of mold resistant drywall.
Mold can develop within 24 to 48 hours of a flood, says Ashley Small of FEMA, so remove wet contents, including carpeting and bedding, as soon as possible. If an item has been wet for less than 48 hours, it may be salvageable. However, you’ll need to decide whether it holds enough monetary or sentimental value to try to do so. And notify your insurance company before removing items to ensure that you’re not affecting coverage. Always photograph the flood-soaked items.
Damage from long standing water falls in this class, like river flooding or storm surges from a hurricane. It has saturated materials such as stone, brick, and hardwood. These materials have low permeance — meaning they do not soak up liquids quickly. Time is the primary factor in this category. With a higher cost of cleanup and repair, it is important to get problems diagnosed and solved as quickly as possible.

If the moisture damage has been neglected or gone unnoticed for long, you’re likely to find rot. Where possible, remove and replace soft, spongy studs and wall sheathing. Where removal is difficult, treat the affected areas with a wood preservative (available at home centers), after cleaning the wood and allowing it to dry. Then double up rotted members with pressure-treated wood.

If it snows where you live, be wary about the formation of ice dams on your roof. This happens when the heat inside your home causes water to melt in the middle of your roof. The water then refreezes near the edges, forming a dam that prevents melting snow from draining off the roof. The water that backs up can leak into your home and damage ceilings, walls and other areas of your home. To prevent ice dams from forming, insulate your attic to keep heat from rising and reaching the roof.

To further ensure a safe and effective environmental remediation, our crews are rigorously trained in mold removal procedures approved by the Indoor Air Quality Association (IAQA); Institute of Inspection, Cleaning and Restoration Certification (IICRC);  the Restoration Industry Association (RIA); and our own in-house trainers. In addition, all of our superintendents, operations managers, project managers, project directors and regional managers  hold Certified Mold Remediation (CMR) certifications.
Inspect damaged materials for mold and mildew. Mold can start to grow in the right conditions in as little as 24 hours. For long-term issues, like mold caused by attic condensation, the mold may have started growing a long time ago. And if you find mold and mildew issues, you need to be very careful. Some mold is toxic to humans, and all mold is very damaging to the materials it infests. For small mold issues, cut out the material, bag it, and throw it away immediately. For serious mold issues, get out of the area, shut down any airflow (to avoid spore contamination) and call a professional. And keep in mind that mold can show up in hidden areas like inside walls or under floors, so this inspection and water damage repair will be ongoing.
Regular cleaning may maintain household furniture’s upkeep but with Dallas Water Damage’s advanced cleaning technology, our technicians can fully restore your furniture in their brand new state while keeping them free from bacteria and viruses that may cause common health problems. Our competitive pricing options vary depending on your water damage and professional cleaning needs. You may call our 24 hour emergency call-in service for a free estimate today.

A leaky faucet, cracked bathtub, or failing toilet can easily become a much larger and costlier problem. A 120-square foot bathroom can cost as much as $3,000 to clean up and repair. Homeowners spend an average of about $300 when hiring a plumber, but can save thousands in future expenses. More importantly, homeowner's insurance typically does not cover damage due to ignored maintenance issues.
In addition, it’s important to have a working flashlight and turn off all water and electrical sources within the home, says Dr. Maurice A. Ramirez, author of “The Complete Idiot’s Guide to Disaster Preparedness.” Even if the power isn’t operational, it’s a good idea to go to your fuse box and turn off the main, plus all of the individual fuse connections. That way, if the power is reactivated, you’re not at risk for mixing standing water and electricity.
Coastal Surge: If you live by the ocean, rising tides and seasonal storms can cause flooding to your property. When a high tide corresponds with a storm, it can be a recipe for disaster. As well as those right along the coast, other properties set slightly off from the ocean can also be at risk. High winds from the storm can also help water infiltrate and damage buildings and land.

Water damage is a serious problem that needs immediate attention fast. The faster water damage is treated, the more furniture and valuable items are saved from permanent damage. Water damage may happen at any time and the most common cause is flooding. Floods may be caused by natural disasters such as hurricanes and excessive rainfall. Sometimes flooding may occur due to leaking faucets, broken sewage pipes, and waste buildup under sink drains.
Expert Rytech technicians will apply state-of-the-art drying process techniques to your property and issue a full written report to Olympus upon completion. Rytech gives you the added security and assurance of specialists who carry visible identification, arrive in clearly marked Rytech vehicles, and wear protective footwear to avoid soiling undamaged areas of your property.
Black water contains pathogenic agents and is grossly unsanitary. Anyone with a compromised immune system, respiratory problems, or allergies, as well as young children and the elderly must remain off the job site until the building is judged safe for occupancy. Black water includes sewage and other contaminated water sources entering or affecting the indoor environment, such as: toilet backflows, flooding from seawater, ground surface water, and rising river water. Category 3 water can contain contaminants such as pesticides, heavy metals, or toxic substances.
When a disaster of this magnitude occurs, the first things a plant will need are lighting and pumps. This requires the use of on-site generators and temporary power connections. It's highly recommended to not allow the plant distribution system to be back-fed. If a motor is required to turn a pump, a portable motor starter fed by the generator should be installed on a temporary panel next to the motor.

All water damage restoration jobs are unique and the amount of work required for each depends on a variety of factors such as the amount of area in the home that’s been damaged and how long the water has been present. Once a professional water damage cleanup vendor arrives and has a chance to inspect the home, they’ll be able to put together a detailed project timeline specific to your job. In the meantime, we’ve listed the eight common phases that occur during the water damage restoration process and what happens in each, so you’ll know what to expect.
If the home is habitable, take precautions to keep yourself and your family safe from injury. Use flashlights to move around dark rooms, for example. If the home isn’t habitable, don’t try to stay there. Move to a shelter or alternate location. Consult your insurer to find out what provisions the company will make for temporary housing while your home is being repaired.
If you repair damage resulting from an appliance-related leak, you need to get a Certificate of Appliance-Related Water Damage Remediation (WDR-1). The certificate verifies that the damage was properly replaced or repaired and that any related physical damage was properly remediated, repaired, or replaced. If you don't have the repairs or remediation certified by a WDR-1, an insurance company can deny you coverage in the future based on previous appliance-related damage or claims.

Policyholders don’t want hassles.  We’ll make sure you get the coverage you paid for, remove the headache of having to work with your insurance company, and streamline the entire process.  You have enough to worry about; we’ll work with your insurance company to achieve your complete satisfaction.  In fact, we’ll usually do a survey with the insurance companies to make certain each and every policyholder gets everything they are entitled to get.
Category 2 Water - Refers to a source of water that contains a significant degree of chemical, biological or physical contaminants and causes discomfort or sickness when consumed or even exposed to. Known as "grey water". This type carries microorganisms and nutrients of micro-organisms. Examples are toilet bowls with urine (no feces), sump pump failures, seepage due to hydrostatic failure and water discharge from dishwashers or washing machines.
×