Inspect damaged materials for mold and mildew. Mold can start to grow in the right conditions in as little as 24 hours. For long-term issues, like mold caused by attic condensation, the mold may have started growing a long time ago. And if you find mold and mildew issues, you need to be very careful. Some mold is toxic to humans, and all mold is very damaging to the materials it infests. For small mold issues, cut out the material, bag it, and throw it away immediately. For serious mold issues, get out of the area, shut down any airflow (to avoid spore contamination) and call a professional. And keep in mind that mold can show up in hidden areas like inside walls or under floors, so this inspection and water damage repair will be ongoing.
To further ensure a safe and effective environmental remediation, our crews are rigorously trained in mold removal procedures approved by the Indoor Air Quality Association (IAQA); Institute of Inspection, Cleaning and Restoration Certification (IICRC);  the Restoration Industry Association (RIA); and our own in-house trainers. In addition, all of our superintendents, operations managers, project managers, project directors and regional managers  hold Certified Mold Remediation (CMR) certifications.
Ice dams and other roof problems can also cause water damage to siding materials as well. Here, the biggest danger is water seeping in behind your siding and causing permanent damage to more vulnerable materials. So if this happens, you will need to remove or replace the siding quickly before rot sets in. Water can also seep in behind faux stone and other external walls around your home. So it’s important to be thorough in this inspection.
Among the most common and most preventable causes of water damage are burst pipes. Burst pipes typically happen because of clogs and freezing. Prevent the damage by finding a family plumber to do annual inspections. Regular inspections and maintenance are a cost-effective, preventative measure. Installing new plumbing typically runs between $350 to $2,000.
Restoration dehumidifiers are an important piece of restoration drying equipment. Humid environments are ripe for the development of mold and bacteria, so drying them quickly and effectively is important. You can find a wide range of different types of dehumidifiers, varying in size and capacity and the choosing the right one will depend on the types of environments in which they are used.
Accurate mold and tooling component assembly is a critical step in mold repair—and is the origin of many preventable, unscheduled mold stops (breakdowns). Poor workmanship and mistakes are usually a result of too much speed, lack of focus or physical skills, and disorganized work habits. If several repair techs are involved in the assembly of a mold, communication breakdowns between them can require the mold to be disassembled yet again to correct an oversight or install something that was forgotten.
If you have to remove mold concentrations or perform any black mold removal covering more than a few square feet, where the musty odor is strong or where you find extensive water damage, we recommend that you take special precautions. You want to not only avoid contaminating the rest of the house but also protect yourself from breathing high concentrations of spores and VOCs.
The European-American community was founded by David Hill, Isaiah Kelsey, and Richard Williams, who arrived in the Tualatin Valley in 1841, followed by six more pioneers in 1842. The locality went by two other names—East Tualatin Plains and Columbia—before it was named “Hillsborough” in February 1850 in honor of Hill, when he sold part of his land claim to the county.
Mark the damaged drywall with a pencil after you determine the area of drywall you want to remove. Use a straightedge to mark lines vertically and horizontally on the face of the drywall. Whenever possible, have the lines fall over the centers of the framing members behind the drywall; this will provide backing and a fastening surface for the drywall patch.
While the mold was still being disassembled, two “cleaners” began pulling tooling out of plates and putting them into buckets in preparation for a good scrubbing—and I mean a scrubbing. Immersing the buckets into a solvent tank, they used their hands like wire whisks as they swished the close-tolerance ejector sleeves around, effectively removing any trace of vent residue or “track” marks on the tooling—and in the process maybe adding some marks of their own.
Different removal methods and measures are used depending on the category of water. Due to the destructive nature of water, chosen restoration methods also depend heavily on the amount of water, and on the amount of time the water has remained stagnant. For example, as long as carpet has not been wet for longer than 48 hours, and the water involved was not sewage based, a carpet can usually be saved; however, if the water has soaked for longer, then the carpet is probably irreparable and will have to be replaced.[8] Water damage restoration can be performed by property management teams, building maintenance personnel, or by the homeowners themselves; however, contacting a certified professional water damage restoration specialist is often regarded as the safest way to restore water damaged property.
×