“Last December we discovered a leak underneath our kitchen that caused extensive damage. We called WaterBear and they came out that day. The people who came to our house were always respectful, kind and efficient. They did exactly what they quoted us and did it in a timely manner. All of our questions and concerns were answered in a timely manner, also.   They helped us through this very difficult situation. I hope we never have another problem like this, but if we did, I would call WaterBear.” – Anne M.
"Using truck-mounted vacuums with 2,000 horsepower, and dehumidifiers, we can extract moisture from furniture, hardwood, tile, even Sheetrock," Kent says. Even electronics like TVs and laptops may still operate after a thorough drying. "In fact, when carpet gets wet, people think it's ruined, but it actually ends up stronger than when it was made," Kent says.
It’s important to understand the differences because Category 2 and Category 3 water present health risks to your employees and customers and need to be handled differently. The most likely sources of clean water would be water from a pipe, water heater, steam lines or even rainwater. The basic rule of thumb is that it should look and smell like tap water.
The project documentation manager should make sure the camera memory sticks are downloaded to a folder located on the site server. Each picture will be opened and saved in a folder labeled by the appropriate power center or room number. There are two pictures associated with each piece of equipment, both of which should be labeled using the sequence number. After saving the pictures on the local server, the memory sticks will be erased and ready for use the next day.
Clean water that originated from a source that does not pose substantial harm to humans. Examples include: broken water supply lines, melting ice or snow, falling rainwater, broken toilet tanks, and toilet bowls that do not contain contaminants or additives. Clean water may deteriorate with time as it dissolves or mixes with soils and other contaminants.

The electrical systems in modern cars are particularly prone to flood water damage. Engine control computers, vehicle sensors, infotainment systems, and other electronic devices – along with wiring harnesses and the many connectors that join them together – can be very difficult to salvage. Unless every part is thoroughly cleaned and dried, inside and out, problems caused by corrosion can crop up weeks or even months after the flooding.
After this type of catastrophic event, it's typically best to replace certain types of equipment rather than try to recover items such as receptacles, light switches, start-stop stations, fire alarm panels, and metering equipment. Your crews must also drain all the conduits by opening up the conduit covers and letting gravity drain out all water and debris.
Once any standing water has been removed, it’s time to start drying out the home. Your contractor will bring in different types of air movers (think of these like glorified fans) to help circulate airflow throughout the room. Don’t be surprised if they need to lift up a section of the carpet or position one of the air movers at certain sections of the walls to ensure air is getting to the most saturated parts of the room. If you have hardwood floors, they may use floor mats which help draw the water out of the floor. If needed, they might even remove the baseboards and drill holes into the drywall to help the walls dry faster. While some of these methods may sound extreme, they’re making every effort to dry the home without having to demolish and rebuild, which could add multiple weeks to the project timeline and become very costly.
During the walkthrough, compile a list of flooded equipment to help you estimate man-power requirements and create a preliminary schedule of repair work. As mobilization of crews begins, start developing job strategies, such as finding office space, living accommodations, and transportation for crews. You must also think about arranging food/catering services and developing work schedules. Once your crews have been mobilized and job-site safety requirements are met (see SIDEBAR: Developing a Safety Plan Following a Natural Disaster), it's time to go to work.
Regular cleaning may maintain household furniture’s upkeep but with Dallas Water Damage’s advanced cleaning technology, our technicians can fully restore your furniture in their brand new state while keeping them free from bacteria and viruses that may cause common health problems. Our competitive pricing options vary depending on your water damage and professional cleaning needs. You may call our 24 hour emergency call-in service for a free estimate today.
We can provide dehumidification for your property. This goes along with the mold removal and prevention process. The living areas of your home should not have humidity; this is normally taken care of by your central air conditioning system. However, if your AC ductwork has a crack or leak, or if your home does not have central air, the interior of your house may sometimes have damp or humid air. The dehumidification process eliminates that and saves you the headache of mold removal down the road.

Laser is an acronym for “Light Amplification by the Stimulated Emission of Radiation.” This technology produces a sharply focused beam of hot light that melts a very small area of metal and can be used to join similar or dissimilar alloys. The laser welding process can be performed quickly (normally in milliseconds) and does not scar or blemish the welding surface. In fact, by adjusting the laser’s beam diameter, a smooth, near polished finish can be achieved with the laser welder. Since very little heat is generated at the weld point, users can easily weld 0.10mm away from the most complicated and intricate machined patterns, polished surfaces and removable component assemblies.


You have to open up the wall to get at the mold growing inside. Since you have to repair the wall anyway, don’t hesitate to cut the drywall back beyond the obvious damage to find all the mold and let the wall dry out. To avoid cutting electrical wires, poke a hole through the damaged section and locate the wires first. Turn off the power to the outlets before you cut. Mist the moldy drywall and insulation with the pump sprayer to avoid spreading mold spores. Double-bag moldy material in heavy-duty plastic bags and tie them shut.
You may also wish to hire a flood restoration service—you can find pros under “Flood” or “Disaster recovery” in your local phone book, or check with the Better Business Bureau, local Chamber of Commerce, or contractor recommendation sites, such as Angieslist.com or MerchantCircle.com. Look for those with Institute of Inspection, Cleaning, and Restoration Certification.
We are the most trusted name in property damage restoration because we don’t outsource and you can trust our workers when they are in your home. They are specially trained and industry certified. You will be assigned a Project Manager who will walk you through the entire process step-by-step.  The team leader is plugged into your job every single day. No exceptions.
Most insurance policies will pay to remove mold only if it must be removed to repair or replace property that was damaged by a covered peril. You must report water damage that was hidden from view within 30 days of the date you first noticed it. Some companies provide a limited amount of mold remediation coverage, and other companies will allow you to buy additional coverage for mold remediation by endorsement.
Restoration dehumidifiers are an important piece of restoration drying equipment. Humid environments are ripe for the development of mold and bacteria, so drying them quickly and effectively is important. You can find a wide range of different types of dehumidifiers, varying in size and capacity and the choosing the right one will depend on the types of environments in which they are used.
×