Hillsboro homes that are left vacant with no regulating of heat or poorly insulated walls can be a common culprit of frozen water pipes and frozen water lines in the winter time. These breaks can be hard to notice immediately because they commonly occur in the basement. Broken pipes can also be common cause of water damage, causing gallons of water to come flooding through your living rooms, bedrooms, kitchen and bathroom. Water pipe bursts are common in areas of extreme winter cold and high winds that drive the wind chill well below freezing temperatures. Pipes that lack proper insulation and are exposed to the winter’s cold are far more likely to create a need for restoration.

Throughout the drying process, crews will stop by periodically to monitor how the drying is progressing. Specifically, they monitor the dehumidifiers’ intake and output temperatures and humidity levels to make sure the dehumidifiers aren’t putting wet air out into the room. They’ll also go back and take readings of the same surfaces they did during the inspection phase. As rooms are declared dry, crews will often move equipment around to other areas of the home that are still wet.
A dark, damp crawl space allows mold to flourish, which can then cause structural damage. Moisture dripping through the concrete foundation of your home can cause basement leaks. Air leakage into the section between the attic and the home can cause moisture on the underside of the roof, which can lead to mold and rotting. Check your home periodically, and look for light fixtures that are look as well as the overall quality of any noticeable piping.
Position the drywall section in the opening, and use a helper to hold the new drywall in place. Install fasteners through the drywall into the wall or ceiling framing. You can use drywall nails or drywall screws. Screws are better because they cause much less damage to the internal structure of the drywall sheet during installation. Install fasteners every 9 inches on the perimeter, and every 12 inches in the field. If necessary, use a piece of plywood or one-by lumber for a backing and fastening surface behind any drywall edges that don't fall over framing.
When there’s been water, fire, tornado or flood damage to your home or commercial business it’s difficult to know who to call to help clean up and repair the property. The answer is easy! Mr. Restore is a Dallas restoration company that provides comprehensive restoration services, as well as environmental remediation. Contact Mr. Restore today, and we can be at your property in 60 minutes!
Most of us are very familiar with lockout/tagout procedures, test-before-touch practices, and applying safety grounds. While these are key safety aspects of putting equipment into an electrically safe condition, there are other safety items that need to be addressed when working in a natural disaster area. Items such as air quality, structural issues, and chemical spill exposure come into play. It is the responsibility of each company to keep its own people safe and supply them with special personal protective equipment (PPE), such as rubber boots, respirators, dust masks, portable gas monitors, and rubber gloves. As a service company, you must also coordinate with plant safety personnel you've contracted with to develop special safety procedures to address the ever-changing site conditions. Frequent safety meetings are a must to keep everyone up to date with the most current hazard conditions on the site.
If you still do not understand why something isn't covered, and you think there is a chance for a review of your situation, don't be afraid to ask your agent or representative for a review or a second opinion. In a stressful situation like a claim, it is understandable that things may not be expressed clearly on either side. You want to make sure you understand fully.

Steven Johnson worked as a toolmaker for 26 years, rebuilding and repairing multicavity molds for Calmar Inc. and then as mold-maintenance engineer for Hospira Inc., a medical device manufacturer. Today, he is the maintenance systems manager for Progressive Components and has his own business, MoldTrax in Ashland, Ohio, which designs and sells software for managing mold maintenance (www.moldtrax.com). He can be reached at [email protected] or (419) 289-0281. 


You can easily spot the most visible type of mold, called mildew, which begins as tiny, usually black spots but often grows into larger colonies. It’s the black stuff you see in the grout lines in your shower, on damp walls, and outdoors on the surfaces of deck boards and painted siding, especially in damp and shady areas. A mildewed surface is often difficult to distinguish from a dirty one. To test for mildew, simply dab a few drops of household bleach on the blackened area. If it lightens after one to two minutes, you have mildew. If the area remains dark, you probably have dirt.
Repairing mold-damaged drywall is not difficult, but correcting the cause of the mold can often be challenging. Roof leaks, an improperly installed vapor barrier, leaky pipes, or constant contact with water from sinks, tubs, and showers can cause mold damage. Mold happens whenever moisture is constantly present. Mold spores attach to the paper facing of the drywall, the paper becomes a food source, and the mold colony propagates and grows. Long-term exposure to mold spores can be harmful, especially if a person is allergic to mold. You should consider consulting a mold removal specialist to determine the type of mold that is present, and you should always wear a face mask and gloves when working with mold.
Our water extraction team offers water extraction services for any home, apartment building, office building, retail store, warehouse, commercial property, condominium, hotel, motel or any other structure that may be in need. Do not hesitate to call our offices to discuss your water extraction needs, no matter how large or how small. We will be happy to discuss your options, the services we offer, and our insurance claims process.

Mold is a major-league nuisance. It blackens the grout lines in your shower, discolors drywall, shows up as black spots on siding, darkens decks, and grows on and rots damp wood everywhere. Even worse, it can be bad for your health. Mold releases microscopic spores that cause allergic reactions, runny noses and sneezing, as well as irritating, even injurious, odors. We’ll cover how to remove mold, how to get rid of black mold, how to kill mold on wood and what kills mold in a few steps.

The average homeowner spends $7.00 per square foot for professional cleanup. That does not include the amounts for repairing and replacing items. Typically, anything that can absorb the contaminants in black water should be replaced, including upholstered furniture, beds, carpets, clothing, and all permeable building materials. Replacement is often more cost effective than restoration.

Drywall repair cost about $500 on average with a typical range of $250 to $750, but can cost much more or less depending on the destruction. It is used in most modern homes and is found in almost all finished areas of a house, including bathrooms. When it becomes wet, it typically needs to be replaced. Not only is the drywall itself ruined, but the wet paper backer of the drywall becomes an excellent environment for mold growth.


In mold repair, structure is especially critical when working with many pieces of close-fitting tooling that are nested into plates. Remembering the type, fit, relational position of components, and the sheer volume of tooling in some molds can be overwhelming enough without adding confusion about where you are in the process of the repair. In shops where two repair techs are usually assigned to a mold, time can be saved by working in a organized approach.
Laser welding, combined with targeted material selection and hardness matching, results in a gate repair that surpasses what can be achieved with traditional methods that match the base material and the filler. The laser welding process permits the use of a wide range of dissimilar metals, allowing selection of a filler metal that will result in optimal performance. Laser welding can be used to combine many different materials, including P-20, Beryllium Copper (BeCu), Stainless Steel, S-7, H-13, and others. One of the most common marriages of materials is Stainless Steel to BeCu, which maintains the cooling properties of BeCu while adding a better wear surface in the Stainless Steel. For example, a 410 stainless steel filler can create a fine martensitic microstructure, delivering optimal wear without compromising the mold’s ability to withstand flexing during injection.
Though not the most common precipitator of water damage repair in the NH, storm flooding can cause serious short term and long-term problems to your residential or commercial property. The likelihood of flood-water damage to your property is rising, and property owners need to be prepared to deal with this very real possibility.  Flooding from seasonal storms is more common than you’d think, and the problems that arise from it need to be addressed as quickly as possible.
And even if you do have flood insurance, you should make sure what is covered. "Many people don't realize their homeowner insurance doesn't cover rising water," says Kent. In other words, "some flood insurance will cover rain water if it comes through your roof, but most of the time, it won't cover water rising in your home, like what's happening in Texas, unless you ask for it specifically."
Also, a combination of moisture and humidity can cause mold to grow as well as any unrepaired water leaks. For instance, if the your air conditioning unit is set to a temperature that causes condensation on your windows then common sense should tell you that your windows may not be the only places with condensation or moisture. (between the walls) If there is already mold growing, these temperatures that cause condensation will only feed the mold to grow.
A leaky faucet, cracked bathtub, or failing toilet can easily become a much larger and costlier problem. A 120-square foot bathroom can cost as much as $3,000 to clean up and repair. Homeowners spend an average of about $300 when hiring a plumber, but can save thousands in future expenses. More importantly, homeowner's insurance typically does not cover damage due to ignored maintenance issues.

How to remove mold and how to perform black mold removal can be done with ordinary household cleaning products. But disturbing big infestations of mold on bathroom walls and other places can be bad for your health, particularly if you are an allergy sufferer or have a weakened immune system. When you discover an extensive mold problem, we recommend that you use the rigorous protective measures we show in Photos 1 – 6, or consider calling in a professional, who knows what kills mold, to handle the problem of how to remove mold. (Search “Industrial Hygiene Consultants” or “Environmental and Ecological Consultants” online to find out how to remove black mold and black mold removal cost. Or call your local public health department on how to get rid of black mold.) And even if you hire pros, read through this article and make sure they follow similar precautions on how to get rid of mold and to keep the mold from spreading throughout your house.

Among the most common and most preventable causes of water damage are burst pipes. Burst pipes typically happen because of clogs and freezing. Prevent the damage by finding a family plumber to do annual inspections. Regular inspections and maintenance are a cost-effective, preventative measure. Installing new plumbing typically runs between $350 to $2,000.

Drywall repair cost about $500 on average with a typical range of $250 to $750, but can cost much more or less depending on the destruction. It is used in most modern homes and is found in almost all finished areas of a house, including bathrooms. When it becomes wet, it typically needs to be replaced. Not only is the drywall itself ruined, but the wet paper backer of the drywall becomes an excellent environment for mold growth.
With a flexible schedule — the Service teams operates a four-shift schedule for full coverage — we can accommodate both planned and emergency repair and ECN jobs, regardless of whether Decatur originally manufactured the mold or not. We also maintain our own fleet of delivery trucks available for pickup and delivery. The fleet is operational 24 hours a day, seven days a week, to help you keep your production downtime to an absolute minimum.
At WaterBear, our water damage Hillsboro specialists understand that a flood in your home or business is emotionally devastating. It takes up valuable time and wreaks havoc on your day-to-day activities. That’s why we offer the best in drying technology, equipment and training to get you back to the life you’re used to as quickly as possible. Our proprietary Dry-In-Place technology places us among the nation’s leaders in Water Damage Mitigation. From our years of experience we have learned that a quick response is the key to limiting damage and potential mold growth in any water damage situation. We strive to get your life back to the way you want it as quickly as possible.
Air movers help to ventilate the affected area, circulate air so that the moisture can be extracted by dehumidifiers and dry damp materials such as drywall and floors. There are a number of different types of restoration air movers and the best choice for you will depend on the planned application of the equipment. The ideal equipment should have the perfect balance of horse power and amp draw. 
×