Remove all of the drywall from the wall if the wrong type of drywall was initially installed. On rare occasions, mold damage results from using the wrong type of drywall for a particular application. The two most common causes of mold damage, not created by water leaks, are drywall installed behind tile, or regular drywall installed in a bathroom instead of mold resistant drywall.

Policyholders don’t want hassles.  We’ll make sure you get the coverage you paid for, remove the headache of having to work with your insurance company, and streamline the entire process.  You have enough to worry about; we’ll work with your insurance company to achieve your complete satisfaction.  In fact, we’ll usually do a survey with the insurance companies to make certain each and every policyholder gets everything they are entitled to get.
In December, while over at my friend's house I heard an explosion and I didn't know what it was or what happened but I guess her pipes had frozen and that turned into a huge flood in her basement. The water increased quickly and we didn't have any idea what to do or who to call and so I looked up emergency water damage and found Nashville Water Damage Flood Repair who came out very quickly and shut the water off so that the problem could be dealt with. These guys really knew their stuff as they shut the water off and begin removing all of the water that it built up in the basement. Luckily for us that there wasn't a whole lot of valuables except for a dresser in the basement that my friend wanted to keep and so most of their efforts were just about removing all of the water from the basement which they did a great job of it took a day or so but they got the job done and they did it right.
When you’re sure the mold has been eliminated, seal the wood surfaces with pigmented shellac like BIN or an oil-based primer like KILZ. Repaint cleaned wall surfaces with a regular latex paint that contains a mildewcide to help stop future mold growth. Then install new insulation and drywall and nail the trim back on. And keep in mind that if the moisture returns, mold will return.
Position the drywall section in the opening, and use a helper to hold the new drywall in place. Install fasteners through the drywall into the wall or ceiling framing. You can use drywall nails or drywall screws. Screws are better because they cause much less damage to the internal structure of the drywall sheet during installation. Install fasteners every 9 inches on the perimeter, and every 12 inches in the field. If necessary, use a piece of plywood or one-by lumber for a backing and fastening surface behind any drywall edges that don't fall over framing.
Since you should notify your insurer soon as possible after the flood, it’s a good idea to keep your insurance company and local agent’s phone number in your always-ready emergency bag. (Note that the NFIP works through private insurance companies, so you contact your insurer just as you would for any other type of claim). In cases where a flood has affected a region or community, your agent may be busy handling his or her own flood issues. In that case, contact the insurance company’s headquarters. 

If the flood was serious enough for you to leave your home, be sure you stay safe upon your return. The Federal Emergency Management Agency warns that you should check for any visible structural damage, such as warping, loosened or cracked foundation elements, cracks, and holes before entering the home and contact utility companies if you suspect damage to water, gas, electric, and sewer lines.  


The information and advice contained in this article is intended as a general guide for informational purposes only. It does not take into account your personal situation. While we at Resolve have significant experience and history operating in the home restoration industry and working closely with construction contractors, we are not licensed as a general or specialty contractor. We encourage you to consider the information we’ve provided but urge you not to rely upon it in place of appropriate professional advice from a licensed, experienced construction contractor.    
It’s important to understand the differences because Category 2 and Category 3 water present health risks to your employees and customers and need to be handled differently. The most likely sources of clean water would be water from a pipe, water heater, steam lines or even rainwater. The basic rule of thumb is that it should look and smell like tap water.
Once help arrives, the first thing a water mitigation contractor will do is inspect the home and evaluate the damage. In order to properly evaluate the damage, they have special tools and instruments they use to measure the moisture content of the home. To do this, they either poke or rest the instruments on top of surfaces like floors, baseboards and ceilings in the damaged rooms to get an accurate reading. Depending on the moisture content readings and Institution of Inspection Cleaning and Restoration Certification (IICRC) dry standards for the state you live in, your contractor will assess if drying equipment is needed.

Dealing with disasters such as flooding, fire, sewage, and more can be stressful. Often, these situations occur unexpectedly – do you know who to call if it happens to you? 1-800 WATER DAMAGE is the trusted name in restoration services. We have over a decade of industry-leading experience and are backed by BELFOR, the world’s largest property restoration company. Our highly-trained professionals have the tools and knowledge necessary to get your property looking like new again.

Flooding in a home can lead to more problems than just water damage and health issues, it can also cause rusted pipes and mold growth.  We use water detection probes and sensors to find these hidden flood damage problems so that we can repair them as part of the restoration process.  You can be confident that our flood damage restoration experts will be thorough and complete and if you made an insurance claim, we can help you coordinate the payment with your insurance provider.
Sewage back‐ups, pipe leaks and breaks not only cause sewage damage, but result in dangerous conditions that require meticulous cleanup to ensure a return to a safe environment. That’s why WaterBear leads in industry standard guidelines and takes every precaution to contain contamination within exposed areas, then thoroughly cleans and decontaminates them. We work to return the areas to their original state – fresh, clean and safe.
The water restoration process is an important one. Using the right procedures and materials can help people save cherished belongings and even prevent their homes from being condemned. Water restoration companies specialize in mitigating the effects of water, but the success for water damage restoration depends on the severity of the damage and the amount of water that caused the damage. Water restoration companies may hire outside experts to assess a property and determine a water restoration and water removal plan. These water restoration companies typically use high-tech equipment and well-documented procedures to control water damage. Water in basement areas may only require a short cleanup process, but water in other areas of a property will require extensive remediation.

While there are currently no government regulations in the United States dictating procedures, two certifying bodies, the Institute of Inspection Cleaning and Restoration Certification (IICRC) and the RIA, do recommend standards of care. The current IICRC standard is ANSI/IICRC S500-2015.[9] It is the collaborative work of the IICRC, SCRT, IEI, IAQA, and NADCA.

×