If left untreated, water can be a destructive force to any residential or commercial property. It can lead to mold growth, stains, and can jeopardize the integrity of the building. Our restoration specialists can carefully inspect your property to determine the extent of the damage and can create customized solutions for you. With our 24/7 emergency services, you can rest assured you have a trusted team ready to help you.

Mold is a major-league nuisance. It blackens the grout lines in your shower, discolors drywall, shows up as black spots on siding, darkens decks, and grows on and rots damp wood everywhere. Even worse, it can be bad for your health. Mold releases microscopic spores that cause allergic reactions, runny noses and sneezing, as well as irritating, even injurious, odors. We’ll cover how to remove mold, how to get rid of black mold, how to kill mold on wood and what kills mold in a few steps.

In addition to the obvious damage it does to upholstery and carpeting, floodwater is a corrosive and abrasive mixture of water and dirt that works its way into every seam and crevice of a vehicle. Sewage and chemical contaminants may also be present in floodwater, and in coastal areas salt water from ocean storm surges can increase the possibility of vehicle damage and costly auto repairs. Even if a car is mechanically safe to drive, sanitary concerns could make it unwise for you to do so.
You can find out how old your water heater is by looking up the serial number on the manufacturer’s sticker near the top of the water heater. Make sure to regularly inspect your water heater to check for signs of moisture build-up, mold or corrosion. If your water isn’t as hot as it used to be or there’s rust coming from your faucets, it’s time to call a plumber or water heater specialist.
Accurate mold and tooling component assembly is a critical step in mold repair—and is the origin of many preventable, unscheduled mold stops (breakdowns). Poor workmanship and mistakes are usually a result of too much speed, lack of focus or physical skills, and disorganized work habits. If several repair techs are involved in the assembly of a mold, communication breakdowns between them can require the mold to be disassembled yet again to correct an oversight or install something that was forgotten.
Before any mold is released for production (“blue-tagged”), it is imperative to put the mold through a series of final-check bench procedures to verify “All Systems Go” and minimize any opportunities for the mold to be stopped and returned to the shop for something that should have been caught before it was released. Water leaks, heater problems, etc., can be avoided with a final-check procedure.
Flooring repairs typically range between $200 to $500. The type of flooring and the length of time water sits affects the costs of removal and repair. Some types of flooring are more permeable than others. For example, laminates and carpet soak up liquids and degrade the subfloor quickly, whereas hardwood can sit underwater for short periods with little damage. Most tile products are either impervious to liquids or can be cleaned and dried with little or no damage, though the area may need grout work.
Appliance hoses. Broken hoses are among the most common causes of water damage. Regularly inspect hoses and hose fittings on washing machines, icemakers, and dishwashers for kinks, cracks, bulges, or deterioration. Replace standard rubber washing machine hoses every two to five years or more often if they are showing signs of wear. Consider using steel-reinforced hoses for longer life.
Drywall repair cost about $500 on average with a typical range of $250 to $750, but can cost much more or less depending on the destruction. It is used in most modern homes and is found in almost all finished areas of a house, including bathrooms. When it becomes wet, it typically needs to be replaced. Not only is the drywall itself ruined, but the wet paper backer of the drywall becomes an excellent environment for mold growth.
At this stage, put away all measuring instruments and hand tools and focus on how best to clean the tool. The type, frequency, and method of cleaning molds should be based on cycles, hours, or production in conjunction with mold-specific factors (resin, residue, vent location and capacity, tooling concerns, etc.) that will dictate the cleaning level and process.
BRAVO – job well done! Discovered a flood at home in San Francisco – water had been over flowing a 2nd floor sink for 15 hours. Contacted Allied, signed work order on line and workers were at the house within 15 minutes. They brought a truck load of equipment to mitigate the damage. Drying fans were installed, heating pads were placed on hardwood floors, walls and ceilings were opened and drying and dehumidifying tubes installed. Excellent, professional care. Very pleased with their swift delivery of emergency service AND their attention to detail to ensure the water damage was dried out completely.
To further ensure a safe and effective environmental remediation, our crews are rigorously trained in mold removal procedures approved by the Indoor Air Quality Association (IAQA); Institute of Inspection, Cleaning and Restoration Certification (IICRC);  the Restoration Industry Association (RIA); and our own in-house trainers. In addition, all of our superintendents, operations managers, project managers, project directors and regional managers  hold Certified Mold Remediation (CMR) certifications.
All severely warped wood (particularly flooring), rotting wood and wood that has developed mold/mildew problems will need to be replaced. Pry apart damaged boards and thoroughly clean beneath them before replacing them. And if the wood is a structural component of your house, you must be very careful when replacing it so that the structure has the right support during and after the water damage repair project.

Melting Ice & Snow: With spring comes nicer weather, but also the occasional risk of flooding in areas that cannot fully absorb all the water. When temperatures fluctuate from day to day, melted ice can refreeze and cause a whole other set of problems. Due to this hazard, it is extremely important to keep an eye on the weather and fix the problem as soon as it occurs.
Different removal methods and measures are used depending on the category of water. Due to the destructive nature of water, chosen restoration methods also depend heavily on the amount of water, and on the amount of time the water has remained stagnant. For example, as long as carpet has not been wet for longer than 48 hours, and the water involved was not sewage based, a carpet can usually be saved; however, if the water has soaked for longer, then the carpet is probably irreparable and will have to be replaced.[8] Water damage restoration can be performed by property management teams, building maintenance personnel, or by the homeowners themselves; however, contacting a certified professional water damage restoration specialist is often regarded as the safest way to restore water damaged property.
×