Our highly trained technicians are ready to respond immediately to flood or water damage at your Columbus property. We have the experience, expertise, and training to restore your home or business quickly and properly. We use advanced inspection and extraction equipment to find the water and remove it as quickly as possible. Our technicians will monitor and document the drying process to ensure your property is back to normal.
Roofs should be inspected annually. A professional roof contractor can look for exterior and interior warning signs that your roof’s condition may lead to water damage, including cracked or missing shingles and areas where water is prone to pool. An inspection can cost several hundred dollars, but in exchange for your peace of mind, it’s priceless.
For instance, it will be less expensive to restore a basement with an inch of clean water from a burst pipe than to tackle a fix caused by three feet of sewage backup. An inch of clean water would start at around $500 to $1500 to pump out and thoroughly dry it. However, the price of basement drainage repairs can increase up to $10,000 or more depending on the size of the space and the extent of the damage. Budget more when your space has been hit from contaminated sources, like a river flood.
We offer mold prevention services, as any place in your home that has constant moisture is susceptible to mold growth. Mold is often detected by smell, but the problem of mold goes far beyond the odor it creates. Mold creates an unhealthy environment, and many people have severe allergic reactions when they are in the presence of mold or mildew. Any mold that is in your home now must be completely eliminated. More importantly, we can also remove the source of the moisture that allows the mold to begin thriving in the first place. It does no good to get rid of the mold if the conditions remain that allow it to grow again. We can do a thorough assessment of your home and advise you on the best course of action.
While the mold was still being disassembled, two “cleaners” began pulling tooling out of plates and putting them into buckets in preparation for a good scrubbing—and I mean a scrubbing. Immersing the buckets into a solvent tank, they used their hands like wire whisks as they swished the close-tolerance ejector sleeves around, effectively removing any trace of vent residue or “track” marks on the tooling—and in the process maybe adding some marks of their own.
In addition, it’s important to have a working flashlight and turn off all water and electrical sources within the home, says Dr. Maurice A. Ramirez, author of “The Complete Idiot’s Guide to Disaster Preparedness.” Even if the power isn’t operational, it’s a good idea to go to your fuse box and turn off the main, plus all of the individual fuse connections. That way, if the power is reactivated, you’re not at risk for mixing standing water and electricity.
Also, a combination of moisture and humidity can cause mold to grow as well as any unrepaired water leaks. For instance, if the your air conditioning unit is set to a temperature that causes condensation on your windows then common sense should tell you that your windows may not be the only places with condensation or moisture. (between the walls) If there is already mold growing, these temperatures that cause condensation will only feed the mold to grow.
A critical part of any mold maintenance plan is to provide the technicians a historical summary of past issues and corrective actions so they may be aware of longstanding or unresolved issues during repairs. Unfortunately, some technicians skip this first stage until after they get a mold disassembled—and then they stop to research a problem whenever they see or feel something they don’t like.

Gone were helpful clues for the repair technicians who had yet to begin troubleshooting and analyzing mold performance and wear. So now, how will the repair techs determine if the 63-day production run was too long? Or whether the leader pins, bushings, and interlocks were greased properly during the run? And how will they know if all the swishing during cleaning did not create any “dings” in the sleeves that could be blamed on something else instead of poor cleaning practices? Other questions will remain unanswered, too: Does the mold still have excess vent residue in the top right quadrant? Were all the ejector sleeves numbered and in the proper mold position before they were removed?

It is important to hire one of these water damage restoration companies as soon as possible after water damage occurs. Moisture promotes the growth of mold and other organisms, increasing the risk for serious health problems. Mold exposure may aggravate allergy and asthma symptoms, especially in children and people with compromised immune systems. Exposure may also increase the risk for respiratory diseases and other medical problems. Cleaning up immediately can help mitigate the health effects of water damage on everyone in a home or commercial space.

If you’re dealing with anything other than a large incursion, you understandably may be considering handling the cleanup and drying yourself to save money or time. The problem is that cleaning up and recovering from water damage isn’t always as straightforward as it seems. This post highlights 3 key things you need to be aware of when addressing water damage from a minor clean water (or Category 1) incursion.
After a mold has been cleaned, repaired, changed over, and final-checked, it needs to be given a new status and moved to one of three areas—typically racked in holding/storage area, reset in the press, or staged as a back-up mold in a molding-cell operation. It could also go to an outside vender for rebuild or production. You should know where your molds are.
When flooding happens, it would be best to call our Dallas Water Damage office right away. The faster the situation is controlled, the better chances of everything restored in their pre-loss state. Upholstered furniture, Persian carpets, oriental rugs, floor carpets, wooden cabinets, and other valuable home items will undergo full restoration by our Dallas Water Damage quality service technicians.

To prevent water damage, you should replace your washing machine supply hose at least once every five years. Also, resist the temptation to overload your washing machine. Constantly stuffing too many clothes into your washing machine could loosen gaskets and valves or cause cracks. Take good care of your washing machine and your washing machine will take good care of you.
"Using truck-mounted vacuums with 2,000 horsepower, and dehumidifiers, we can extract moisture from furniture, hardwood, tile, even Sheetrock," Kent says. Even electronics like TVs and laptops may still operate after a thorough drying. "In fact, when carpet gets wet, people think it's ruined, but it actually ends up stronger than when it was made," Kent says.
Roofs should be inspected annually. A professional roof contractor can look for exterior and interior warning signs that your roof’s condition may lead to water damage, including cracked or missing shingles and areas where water is prone to pool. An inspection can cost several hundred dollars, but in exchange for your peace of mind, it’s priceless.
Type depends on the source and extent to which it has affected the home. Sources can range from clean water from a burst pipe to black water from sewage backup. Cleanup ranges from $3.75 to $7.00 per square foot. Repairs range from $450 to $7,000. Again, these vary widely depending on the source and extent of damage, whether it's a flooded basement, leaky toilet, or damaged roof.
You have to open up the wall to get at the mold growing inside. Since you have to repair the wall anyway, don’t hesitate to cut the drywall back beyond the obvious damage to find all the mold and let the wall dry out. To avoid cutting electrical wires, poke a hole through the damaged section and locate the wires first. Turn off the power to the outlets before you cut. Mist the moldy drywall and insulation with the pump sprayer to avoid spreading mold spores. Double-bag moldy material in heavy-duty plastic bags and tie them shut.

Almost every home gets mold infestations. The trick is to mold remediation is to get to them before they get big and harm both you and your home. In this article, you’ll learn about mold remediation and how to get rid of mold, how to get rid of black mold and what kills mold. We’ll show you how to identify mold, how to eliminate the small infestations as well as the big ones that have gotten out of hand and how to clean mold. We’ll also answer the question: Does bleach kill mold?
Our plumbing and water damage restoration experts are well-trained and knowledgeable in handling a water damage emergency whenever the situation strikes. Our trained professionals receive the Institute of Inspection, Cleaning and Restoration Certification (IICRC) and they’ll always perform emergency water damage services in compliance with the highest standards for professional water damage restoration. Roto-Rooter’s vehicles are fully equipped with state-of-the art water extraction, drying and moisture testing equipment to handle everything including:
Our plumbing and water damage restoration experts are well-trained and knowledgeable in handling a water damage emergency whenever the situation strikes. Our trained professionals receive the Institute of Inspection, Cleaning and Restoration Certification (IICRC) and they’ll always perform emergency water damage services in compliance with the highest standards for professional water damage restoration. Roto-Rooter’s vehicles are fully equipped with state-of-the art water extraction, drying and moisture testing equipment to handle everything including:
After a mold has been cleaned, repaired, changed over, and final-checked, it needs to be given a new status and moved to one of three areas—typically racked in holding/storage area, reset in the press, or staged as a back-up mold in a molding-cell operation. It could also go to an outside vender for rebuild or production. You should know where your molds are.

Want to avoid large cleanup and repair bills? Preventative maintenance and cleaning up quickly after damage are critical to keeping costs down. How long moisture is left untreated increases the scope of the damage and allows mold to grow. Preventing damage by contacting professionals to diagnose causes and make small repairs can save thousands later. Regardless of cause or cost, always document the damage for insurance claims.
Today’s precision welding shops specializing in plastic injection mold, dies and tooling repair have a wide range of new technologies available to enhance their ability to provide the highest level of quality, craftsmanship, and service to their clients. One of the fastest growing technologies is the use of manual laser welding systems as an alternative to traditional microscope GTA welding.
Molds should never be arbitrarily disassembled without a specific level in mind. To do so is to invite excessive handling of tooling components or over-maintaining a mold, which increases the opportunity for damage and wastes man-hours. Time-based mold disassembly levels (based on cycles, hours, days, or parts produced) should be established to optimize bench time.
You can find out how old your water heater is by looking up the serial number on the manufacturer’s sticker near the top of the water heater. Make sure to regularly inspect your water heater to check for signs of moisture build-up, mold or corrosion. If your water isn’t as hot as it used to be or there’s rust coming from your faucets, it’s time to call a plumber or water heater specialist.
Mark the damaged drywall with a pencil after you determine the area of drywall you want to remove. Use a straightedge to mark lines vertically and horizontally on the face of the drywall. Whenever possible, have the lines fall over the centers of the framing members behind the drywall; this will provide backing and a fastening surface for the drywall patch.
It’s time for one of the most important steps: removing any standing water from the home. The removal process is actually much less complicated than you may think. Contractors use fancy shop vacuums and rotate them around the room, sucking up all the water that’s present in the area. The amount of time this phase takes varies depending on the type of substrate that’s being dried, the size of the room and the total amount of water that’s present.
×